Sharp CX48K4, Service Manual

7

7-1

7-2

CX48K4

PIF ADJUSTMENT

NO. Adjustment part

Adjusting procedure and conditions

Waveform and others

1

Fig. 1

2

RF-AGC
TAKE OVER
POINT
ADJUSTMENT
(I

2

C BUS

CONTROL)

1. Receive "PAL COLOUR BAR" signal.

» 

Signal Strength: 57 ±1 dBµV (75 ohm open)

2. Connect the oscilloscope to TP201 (Tuner’s

AGC Terminal) as shown in Fig. 3.

3. Call "AG" mode in service mode. Adjust the

"AG" bus data to obtain the Tuner output pin
drop 0.1 V below maximum voltage.

4. C h a n g e   t h e   a n t e n n a   i n p u t   s i g n a l   t o

63~67dBµV, and make sure there is no noise.

5. Turn up the input signal to 90~95 dBµV to be

sure that there is no cross modulation beat.

Note:

For the 50 ohm signal strength
gauge, when not using 50/75
impedance adapter, signal
strength is 52 ±1 dBµV(75 ohm
open), instead of 57 ±1 dBµV
(75 ohm open).

Precaution:

The loss of using impedance
adapter

»

 Bias box: About 4.5 V

Oscilloscope

0.1V

TV Set

Bias box

TP201

+

+

–

–

Tuner IFT
(PRESET)

1. Get the tuner ready to receive the E-9 CH

signal, but with no signal input.
Adjust the PLL data.

2. Connect the sweep generator's output cable

to the tuner antenna. (RF SWEEP)

3. Adjust the sweep generator's to 80dBuV.
4. Connect the response lead (use LOW IMPED-

ANCE probe with wave detector; see Fig.1) to
the tuner's IF output terminal. (This terminal
must have the probe alone connected).

5. Set the RF AGC to 0 - 6 V with no saturation

with the waveform.

6. Adjust the tuner IF coil to obtain the waveform

as shown in Fig. 2.

Note: Be  sure to keep the tuner cover in

position during this adjustment.

E-9 CH

P

                C

10k

100k

1n60

75ohm

IF OUT

-1.5+/-0.8dB

1000p

Oscilloscope

Fig. 2

Fig. 3

PURITY ADJUSTMENT

NO. Adjustment part

Adjusting procedure and conditions

Waveform and others

1

PURITY ADJ.

1. Receive the GREEN-ONLY signal. Adjust the

beam current to about 700 µA.

2. Degauss the CRT enough with the degausing

coil.

Note: Follow the Job Instruction Sheet to ad-

just the magnetic field.
Vertical Bv

: -0.050 mT

(-0.50 gauss)

Horizontal Bh : +0.020 mT

(0.20 gauss)

3. Maintain the purity magnet at the zero

magnetic field and keep the static convergence
roughly adjusted.

4. Observe the points a, b as shown in Fig. 4-1

through the microscope. Adjust the landing to
the rank A requirements.

5. Orient the raster rotation to 0 eastward.
6. Tighten up the deflection coil screws.

»

 Tightening torque: 108 ± 20 N (11 ±2 kgf)

7. Make sure the CRT corners landing meet the

A rank requirements. If not, stick the magnet
sheet to correct it.

Note: This adjustment must be done after

warming up the unit for 30 minutes
or longer with a beam current over
700 µA.

Note: Set the service mode by JA122 &

JA124 (short) then press factory proc-
ess R/C RGB key to change to RGB
mono colour mode.

* For the following colours press R/C RGB key

to change.

* Press R/C RGB key for 1 second

in NORMAL MODE, the colour
will change to RGB mono colour
mode.

The TEXT Key "R. G. Cy" Key can
be directly use to change to other
colours screen.

a

b

A

B

A

B

A = B

A = B

Rank "A" 

(on the right of the CRT)

Rank "A"

(on the left of the CRT)

Green-only

Blue-only

Red-only

Signal-colour

screen cleared

Fig. 4-1

Fig. 4-2

Fig. 4-3