Sharp DV-SR84RU Operation Manual Download

Page: 2 / 94

Precautions

Before you start

Power Cord Protection

CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.
AS THE LASER BEAM USED IN THIS UNIT IS

HARMFUL TO THE EYES, DO NOT ATTEMPT TO

DISASSEMBLE THE CABINET. REFER SERVICING TO

QUALIFIED PERSONNEL ONLY.

NOTE:

This unit can be used only where the power supply is
AC 220–240V ~ ± 10%, 50Hz ± 0.5%. It cannot be used
elsewhere.

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR

MOISTURE.

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, AND ANNOYING INTERFERENCE, USE THE

RECOMMENDED ACCESSORIES ONLY.

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPARATUS TO DRIPPING OR

SPLASHING, NO OBJECTS FILLED WITH LIQUIDS,

SUCH AS VASES, SHOULD BE PLACED ON THE

APPARATUS.

Laser Diode Properties

Material:

GaAs

Wave length:

DVD: 658 nm

CD:

790

Emission Duration: Continuous

Laser output:

Max. 19 mW

• This unit is classified as a CLASS 1 LASER product.
• The CLASS 1 LASER PRODUCT marking is embossed on

the rear cover.

• This product contains a low power laser device. To

ensure continued safety,
do not remove any cover or
attempt to gain access to
the inside of the product.
Refer all servicing to qualified
personnel.

Warning of Dew Formation

Moisture may form inside the unit under the following
conditions:
• Immediately after a heater is turned on.
• In a steamy or humid room.
• When the unit is suddenly moved from a cold to warm

environment. If moisture forms inside this unit, it may
not operate properly or damage the video tape. In such
case, turn on the power and wait for more than 2 hours
for the moisture to evaporate.

No Fingers or Other Objects Inside

Do not put your fingers or objects on the disc tray.

Nonuse Periods

• When the unit is not being used, switch the unit to the

standby mode.

• When left unused for a long period of time, the unit

should be unplugged from the household AC outlet.

Location and Handling

S-VIDEO

ANALOG

AUDIO OUT

COAXIAL

DIGITAL AUDIO OUTPUT

PCM/BITSTREAM

IN (AV3)

OUT

AUDIO IN

(AV3)

ANTENNA

OUT

AV2 (DECODER)

AV1 (TV)

COMPONENT

VIDEO OUTPUT

PR/CR

PB/CB

CLASS 1 LASER PRODUCT
CLASSE 1 PRODUIT LASER
PRODUCT CON LASER CLASE 1

• Do not stand the unit vertically. Install the unit in a

horizontal and stable position. Do not place anything
directly on top of the unit. Do not place the unit directly
on top of the TV.

• Depending on the TV, noise or disturbance of the picture

and/or sound may be generated if the unit is placed too
close to your TV. In this case, please ensure enough space
between your TV and the unit.

• Do not cover or place the unit in enclosed spaces to

prevent excessive temperature build up.

• Keep the distances 20cm around apparatus of ventilation

openings.

• Do not place the unit in direct sunlight, or near heat

sources. Do not place any combustible objects on the
device (candles, etc.).

• Depending on the environment, the temperature of the

unit may increase slightly. This is not a malfunction.

• Keep the unit away from strong magnetic objects.
• Do not place any object containing water or other liquids

on the unit. In the event that liquid should enter the
cabinet, unplug the unit immediately and contact the
retailer or service centre approved by SHARP immediately.

• Do not remove the unit cabinet. Touching parts inside the

cabinet could result in electric shock and/or damage to
the unit. For service and adjustment inside the cabinet, call
a qualified dealer or service centre approved by SHARP.

• Be sure to remove a disc and unplug the AC power cord

from the output before carrying the unit.

• Disconnect the mains plug to shut off when find troubles

or not in use.

• The mains plug shall remain readily operable.
• Read both manual instructions to ensure correct and safe

installation and interconnection of the unit in multimedia
systems.

To avoid any malfunctions of the unit, and to protect
against electric shock, fire or personal injury, please
observe the following.
• Hold the plug firmly when connecting or disconnecting

the AC power cord.

• Keep the AC power cord away from heating appliances.
• Never put any heavy object on the AC power cord.
• Do not bundle any cables such as; AC power cord,

Round Coaxial cable or other cables that are used to
connect this unit to your TV together. Or never put
any cables on the top panel of this unit. The noise or
disturbance of the picture may be generated.

• Do not attempt to repair or reconstruct the AC power

cord in any way.