UX-470ES/SE/AT
FO-880ES/AT
CPU Control Interface
MIRQn
135
I
HU
−
Modem interrupt, active low. (Hysteresis In, Internal Pullup.)
SYSCLK
133
I
H
−
System clock. (Hysteresis In.)
TSTCLK
130
O
−
123XT
Test clock.
Bus Control Interface
A[23:0]
[1:6][8:13]
O
TU
123XT
Address bus (24-bit).
[15:20][22:27]
D[7:0]
[136:139]
I/O
TU
123XT
Data bus (8-bit).
[141:144]
RDn
128
O
−
123XT
Read strobe.
WRn
127
O
−
123XT
Write strobe.
ROMCSn
120
O
−
123XT
ROM chip select.
CS1n
122
O
−
123XT
I/O chip select.
CS0n
57
O
−
123XT
SRAM chip select. (Battery powered.)
MCSn
121
O
−
123XT
Modem chip select.
SYNC
126
O
−
123XT
Indicates CPU op code fetch cycle (active high).
REGDMA
124
O
−
123XT
Indicates REGSEL cycle and DMA cycle.
WAITn
125
O
−
123XT
Indicates current TSTCLK cycle is a wait state or a halt state.
RASn
113
O
−
123XT
DRAM row address select. (Battery powered.)
CAS[1:0]n
[111:112]
O
−
123XT
DRAM column address select. (Battery powered.)
DWRn
109
O
−
123XT
DRAM write. (Battery powered.)
Prime Power Reset Logic and Test
DEBUGn
129
I
HU
−
External non-maskable input (NMI).
RESETn
131
I/O
HU
2XO
FC100/FC200 Reset.
TEST
58
I
C
−
Sets Test mode (Battery powered).
Battery Power Control and Reset Logic
XIN
59
I
OSC
−
Crystal oscillator input pin.
XOUT
60
O
−
OSC
Crystal oscillator output pin.
PWRDWNn
62
I
H
−
Used by external system to indicate -to FC100/FC200 - loss of prime power.
(Results in NMI)
BATRSTn
61
I
H
−
Battery power reset input.
WRPROTn
110
O
−
1XC
(Battery powered.) Write protect during loss of VDD power.
NOTE:The functional logic is powered by battery power, but the output drive
is powered by DRAM battery power.
Scanner Interface
START
101
O
−
2XS
Scanner shift gate control.
CLK1
100
O
−
2XS
Scanner clock.
CLK1n
99
O
−
2XS
Scanner clock-inverted.
CLK2
98
O
−
2XS
Scanner reset gate control (or clock for CIS scanner).
FCS1n/VIDCTL0
96
O
−
2XT
Flash memory chip select or Video Control signal.
FCS2n/VIDCTL1
97
O
−
2XT
Flash memory chip select or Video Control signal.
Printer Interface
PCLK/DMAACK
29
O
−
3XC
Thermal Print Head (TPH) clock, or external DMAACK.
PDAT
30
O
−
2XP
Serial printing data (to TPH).
PLAT
31
O
−
3XP
TPH data latch.
STRB[3:0]
[33:36]
O
−
1XP
Strobe signals for the TPH.
STRBPOL/DMAREQ
37
I
C
−
Sets strobe polarity, active high/low or external DMA request.
Operator Panel Interface
OPO[0]/GPO[8]/
47
O
−
2XL
Keyboard/LED strobe [0] or GPO[8] or Scan Motor Power Control
SMPWRCTRL
OPO[1]/GPO[9]/
46
O
−
2XL
Keyboard/LED strobe [1] or GPO[9] or Print Motor Power Control
PMPWRCTRL
OPO[2]/GPO[10]/
44
O
−
2XCT
Keyboard/LED strobe [2] or GPO[10] or RINGER
RINGER
OPO[3]/GPO[11]
43
O
−
2XL
Keyboard/LED strobe [3] or GPO[11]
OPO[4]/GPO[12]/
42
O
−
2XL
Keyboard/LED strobe [4] or GPO[12] or SSTXD1 (for SSIF1)
SSTXD1
OPO[5]/GPO[13]
40
O
−
2XL
Keyboard/LED strobe [5] or GPO[13]
OPO[6]/GPO[14]
39
O
−
2XL
Keyboard/LED strobe [6] or GPO[14]
OPO[7]/GPO[15]
38
O
−
2XL
Keyboard/LED strobe [7] or GPO[15]
OPI[0]/GPIO[21]/
52
I/O
HU
2XC
(Pullup, Hysteresis In) Keyboard return [0] or GPIO[21] or SSRXD1
SSRXD1
(for SSIF1)
OPI[1]/GPIO[22]/
51
I/O
HU
2XC
(Pullup, Hysteresis In) Keyboard return [1] or GPIO[22] or SSSTAT1
SSSTAT1
(for SSIF1)
FC100M (IC8) Terminal descriptions
Pin Name
Pin No.
I/O
Input
Output
Pin Description
Type
Type
(Note: Active low signals have an "n" pin name ending.)
5 – 3
Summary of Contents for FO-880
