background image

Maintenance

 

Cleaning the cabinet

Periodically wipe the cabinet with a soft cloth and a diluted soap 

solution, then with a dry cloth.

Caution:

  Do not use chemicals for cleaning (gasoline, paint thinner, etc.). 

It may damage the cabinet.

  Do not apply oil to the inside of the unit. It may cause 

malfunctions.

Specifications

As part of our policy of continuous improvement, SHARP reserves 

the  right  to  make  design  and  specification  changes  for  product 

improvement without prior notice. The performance specification 

figures  indicated  are  nominal  values  of  production  units. There 

may be some deviations from these values in individual units.

 

General

Power source

AC 110 - 240 V ~ 50/60 Hz

15 V 

 (UM/SUM-1, R20) x 10

DC IN 12 V 

 

Power 

consumption

AC:  Power on: 30 W

DC 12 V: 4.5 A  

Dimensions

Width: 30 - 5/16’’ (750 mm)

Height: 10 - 13/16” (275 mm)

Depth: 11 - 1/16” (280 mm)

Weight 

(without 

batteries and 

accessories)

14.6 lbs. (6.6 kg)

Weight 

(with batteries)

Approximately 18.1 lbs. (8.2 kg)

 

Amplifier

Output power

Front speaker:

RMS: Total 34 watt (17 W per channel

into 3 ohms at 1 kHz, 10% T.H.D.)

FTC: 12.5 watt minimum RMS per 

channel into 3 ohms from 200 Hz to 

20 

kHz, 10% T.H.D.

Subwoofer:

RMS: Total 66 watt into 3 ohms 

at 100 Hz, 10% T.H.D.

FTC: 50 watt minimum RMS into 

3 ohms from 70 Hz to 200 

Hz, 10% 

T.H.D.

Output terminals

Headphones: 16 Ω - 50 Ω 

(recommended: 32 Ω)

Input terminals

Audio In (audio signal):

500 mV/47 k ohms

Mic Input: 200 Ω - 2 kΩ Ø 1/4” (6.3 mm) 

Guitar: 100 kΩ - 1 MΩ Ø 1/4” (6.3 mm) 

 

Bluetooth 

interface

Bluetooth 

Frequency Band 

2.400GHz - 2.480GHz

Compatible 

Bluetooth

 Profile 

A2DP (Advanced Audio 

Distribution Profile), AVRCP (Audio/

Video Remote Control Profile)

Bluetooth

 2.1 +EDR

 

USB (MP3 / WMA)

USB host interface

  Complies with USB 1.1 (Full 

Speed)/2.0 Mass Storage Class.

  Support Bulk only and CBI protocol.

Support file

  MPEG 1 Layer 3

  WMA (Non DRM)

Bitrate support

  MP3 (32 ~ 320 kbps)

  WMA (64 ~ 160 kbps)

Other

  Maximum total number of MP3/WMA 

files is 65025.

  Maximum total number of folders is 

999 INCLUSIVE of root directory.

  The ID3TAG information supported 

are TITLE, ARTIST and ALBUM only.

  Supports ID3TAG version 1 and 

version 2.

File system 

support

  Support USB devices with FAT 

16/ FAT 32.

 

Tuner

Frequency range

FM: 87.5 - 108.0 MHz

Preset

40 (FM station)

 

Speaker

Type

2-way type speaker system

Front Speakers:

3-1/8” (8 cm) - 3 Ω - Full Range 

Subwoofer: 5- 1/8” (13 cm) - 6 Ω 

- Woofer (light-up)

Maximum input 

power

Front Speakers: 34W / Channel

Subwoofer: 66W / Channel

Rated input power

Front Speakers: 17W / Channel

Subwoofer: 33W / Channel

Specifications (continued)

E-22

Summary of Contents for GX-BT9























Reviews: