During hot fan operation
The fan speed will be automatically switched to maintain the room temperature at 22°C.
(After starting the operation, the fan speed will increase from Level 1 to Level 6 within 2 minutes regardless of
the room temperature.)
Quick warming operation: when the room temperature is below 15°C, the unit will operate at a fan speed higher
than Level 6 for approximately 20 minutes.
(FAN SPEED indicator: all indicators will go off from left to right in order)
●
When the humidity is above 65%, the hot fan operation will start automatically to raise the room temperature up
to 20°C.
● Due to the variation of room size, it may be impossible to raise the room temperature to 22°C.
● When the room temperature is 26°C or higher, the operation will stop (AUTO FAN SPEED indicator: on; FAN
SPEED indicator: off), and when the room temperature is 21°C or lower, the operation will start again.
(When the humidity is above 65% and room temperature is 24°C or higher, the operation will stop, and when the
room temperature is 19°C or lower, the operation will start again.)
During cool fan
operation
The unit will start operating at the most suitable fan speed depending
on room temperature and humidity.
(The operation will start at fan speed "3" for approximately 2 minutes
regardless of the room temperature.)
24 25 26 27 28 29 30 31 32 33 34 35
→
←
1
2
3
4
5
6
Temperature (standard)
Humidity
(High)
(Medium)
(Low)
Level Level Level
Level Level
Level
Stop
Operation
E-10
ENGLISH
w
You cannot start the
foot warming operation with
the remote controller.
Main unit/Remote controller
Pip
Pip
●
Plasmacluster ions will be generated in all operation modes.
●
When operation is stopped by pressing the POWER OFF button on the main unit or
the remote controller, the last operation mode will be memorized. (Memory Function)
● The settings of the timers, Plasmacluster Ions Clean mode and Clothes Deodorizing
mode will not be memorized.
●
When the unit is power off or unplug from the outlet, the memory will be erased.
Hot air is projected downwards to warm your feet.
●
The FAN SPEED indicator, the FOOT WARMING indicator, and the
HOT FAN indicator will turn on.
(The FAN SPEED indicator will turn on in orange during foot warming
operation)
Operation
panel
Display panel
●
The settings of foot warming operation are as follows.
Fan Speed: Level 3; Vertical Swing: 10° upward - 40° downward;
Horizontal Swing: 30°
●
With the Automatic Switch-off function, the foot warming operation will
stop automatically after 8 hours of continuous operation.
●
When switching off foot warming operation:
1
All indicators go off
2
Cool fan operation runs for 30 seconds to cool
down the inner unit before operation stops.
●
Do not unplug the unit before the operation stops.
USEFUL FUNCTIONS
Display
Operation panel
Display panel
To cancel the mode, press the
AUTO FAN SPEED button
again or the FAN SPEED
button.
Pip
(orange mark)
Auto Fan Speed mode
Start/Stop foot warming operation
Main unit
Main unit
Remote controller
IG-HH1A_0607.indd 10
2017/06/13 13:24:15
Summary of Contents for IG-HH1A
Page 23: ...E 22 ENGLISH MEMO IG HH1A_0607 indd 22 2017 06 13 13 24 27 ...
Page 45: ...中文 備忘錄 C 22 20170609_IG HH1A_1st indd 22 2017 06 14 16 26 25 ...
Page 46: ...C 23 備忘錄 20170609_IG HH1A_1st indd 23 2017 06 14 16 26 25 ...
Page 47: ...C 24 中文 備忘錄 20170609_IG HH1A_1st indd 24 2017 06 14 16 26 25 ...