background image

Approximately one watt of power is consumed even when the rice cooker is in OFF mode as long as it is
plugged in. To conserve, unplug when not in use.
During warming the power in the parentheses is the average power at a room temperature of 20

o

C.

Model
A.C. Line Voltage (V/Hz)

Power consumption 

Rice cooking (W)

Warming maximum (W)

Warming (average) (W)

Timer 

Type
Setting range

Display 

Capacity (

l

)

Cooking method
Outside dimensions 
(mm.)

KS-COM18

220 / 50 A.C. only

830

118

40

Present time to finish

1 to 24 hours

Process display of clock/cooking/warming

0.36 - 1.8

Direct heating type

Width
Depth

Weight of product (approx.) kg  

Height

296

408

242

4.1

Safety device  

Temperature fuse; 169

o

C  

Cooking Chart

Cooking time may varying, depend on the kind or volume of rice or ingredients.

Cooking time is set at specified voltage, room temperature 20-25

o

C, water temperature 20-25

o

C and

under standard water level.
No need to soak the GLUTINOUS RICE before cooking.
For cooking Kiaw Ngu Glutinous Rice should be reduced a little water.
Use the broken for cooking Congee, it will became better result.

3

MODEL

PROGRAM

KS-COM18

Volume of rice 

(cup)

Time (approx.) 

(hr : min)

PLAIN RICE
BROWN RICE
GLUTINOUS RICE
CONGEE

PORRIDGE
SLOW COOK
CAKE / BREAD 

2 - 10

0:28 - 0:41

2 - 7

0:57 - 1:57

2 - 6

0:55 - 1:03

0.5 - 2.5

0:49 - 1:04

0.5 - 1.5

0:55 - 1:02

        Depending on the water quantity / seasonings / 
        ingredients for cooking.

SPECIFIC INFORMATION

Summary of Contents for KS-COM18




























Reviews: