background image

5

LC-24LE210EH

END OF LIFE DISPOSAL

A. Information on Disposal for Users (private households)

1. In the European Union

Attention: If you want to dispose of this equipment, please do not use the ordinary dust bin!

Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires 
proper treatment, recovery and recycling of used electrical and electronic equipment.
Following the implementation by member states, private households within the EU states may return their used 
electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local 
retailer may also take back your old product free of charge if you purchase a similar new one.
*) Please contact your local authority for further details.

If your used electrical or electronic equipment has batteries or accumulators, please dispose of these separately 
beforehand according to local requirements.

By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery 
and recycling and thus prevent potential negative effects on the environment and human health which could otherwise 
arise due to inappropriate waste handling.

2. In other Countries outside the EU

If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.

For Switzerland: Used electrical or electronic equipment can be returned free of charge to the dealer, even if you don’t 
purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.

B. Information on Disposal for Business Users

1. In the European Union

If the product is used for business purposes and you want to discard it:

Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for 
the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local 
collection facilities.

For Spain: Please contact the established collection system or your local authority for take-back of your used 
products.

2. In other Countries outside the EU

If you wish to discard of this product, please contact your local authorities and ask for the correct method of disposal.

Attention: Your product 
is marked with this 
symbol. It means that 
used electrical and 
electronic products 
should not be mixed 
with general household 
waste. There is a 
separate collection 
system for these 
products.

The battery supplied with this product contains traces of Lead.

For EU: The crossed-out wheeled bin implies that used batteries should not be put to the general household waste! 
There is a separate collection system for used batteries, to allow proper treatment and recycling in accordance with 
legislation. Please contact your local authority for details on the collection and recycling schemes.

For Switzerland: The used battery is to be returned to the selling point.

For other non-EU countries: Please contact your local authority for correct method of disposal of the used battery.

Summary of Contents for LC-24LE210EH









Reviews: