26
Turning on the power
Press
POWER
on the TV/DVD, or
POWER
on the
remote control.
• POWER indicator (Green): The TV/DVD is on.
(“Please wait” will appear for a few seconds on the
screen.)
Select the DVD mode
Press
TV/DVD
to select the DVD mode.
Turning off the power
Press
POWER
on the TV/DVD, or
POWER
on the
remote control.
• The TV/DVD enters standby mode and the image on the
screen disappears.
• The POWER indicator on the TV/DVD changes to Red.
NOTE
• If you are not going to use this TV/DVD for a long period
of time, be sure to remove the AC cord from the power
outlet.
• Weak electric power is still consumed even when
POWER
is turned off.
Preparation
Perform the following steps before you press
POWER
on the remote control unit.
1
Insert the batteries into the remote control unit.
(See page 10.)
2
Plug in the AC cord to the AC outlet. (See page 9.)
Watching the DVD
Playback procedure
1
Place the disc in the disc slot with the label side
facing forward. (If the disc has a label.) Hold the
disc without touching its surface, align it with the
guides, and place it in position.
• If a disc is inserted during some modes other than DVD
mode, it may switch to DVD mode and then playback
may be begun automatically.
Status display of DVD disc
Press
DISPLAY
. The status display of the disc will
appear on the screen in order like the figure below.
NOTE
• If a non-compatible disc is loaded, “Incorrect Disc”, “Region Code Error” or “Parental Error” will appear on the TV screen
according to the type of loaded disc. If these appear, check your disc again (see pages 6 and 33).
• Some discs may take a minute or so to start playback.
• When an 8 cm disc is placed into the disc slot, and the playback picture or menu display does not appear, press
PLAY
.
• A “Prohibition” symbol “ ” may appear at the upper right of the screen. This symbol means either the feature you tried is
not available on the disc, or the TV/DVD cannot access the feature at this time. This does not indicate a problem with the
TV/DVD.
• When you set a single-faced disc label downwards (i.e. the wrong way up) “Reading” will appear on the display and then
“Incorrect Disc” will be displayed.
• Some playback operations of DVDs may be intentionally fixed by software producers. Since this TV/DVD plays DVDs
according to the disc content recorded, some playback features may not be available. Also refer to the instructions supplied
with the DVDs.
• Do not move the unit during playback. Doing so may damage the disc.
• Use
EJECT
to unload and eject the disc.
• Do not put any objects other than discs on the disc slot. Doing so may cause the unit to malfunction.
• In many instances, a menu screen will appear after playback of a movie is completed. Prolonged display of an on-screen
menu may damage your television set, permanently etching that image onto its screen. To avoid this, be sure to press
POWER
on your remote control once the movie is completed.
• There may be a slight delay between the button is pressed and the function activates.
NOTE
If the TV/DVD does not operate properly:
Static electricity, etc., may affect the player’s operation.
Disconnect the AC power cord once, then connect it
again.
If a disc is inserted during some modes other than DVD
mode, it may switch to DVD mode and then playback may
be begun automatically.
About inserting disc:
If the unit is slanted or moved while inserting disc, the disc
may get damage.
•
•
•
CHAPTER
NO.
DVD
00:15:25 01:41:39
Title 1/3
Chapter
2/24
1/1 Eng Dolby Digital
1/2 Eng
1/1
ELAPSED
TIME
ANGLE NO.
DISC OPERATION
TITLE NO.
TOTAL
TIME
AUDIO LANGUAGE
A KIND OF AUDIO
SUBTITLE LANGUAGE
2
On the screen, “ ” changes to “Reading” and then
playback will commence.
• A menu screen appear on the TV screen, if the disc
has a menu feature. In this case, press
▲
/
▼
/
◀
/
▶
or
ENTER
to operate a menu feature.
3
Press
STOP
to end playback.
• The unit memorizes the stopped point, depending on
the disc. “ ” appears on the screen. Press
PLAY
to
resume playback (from the scene point).
• If you press
STOP
again (“
■
” appears on the screen)
or unload the disc, the TV/DVD will clear the stopped
point.
4
Press
EJECT
.
Remove the disc and then press
POWER
.
The TV/DVD turns off.
• When you eject the disc, you may hear mechanism
noise, but it is not malfunction.
52L0131A.indb 26
52L0131A.indb 26
4/9/09 9:52:31 AM
4/9/09 9:52:31 AM
Summary of Contents for LC 32DV27UT
Page 2: ......
Page 41: ...40 MEMO ...
