Sharp SF-2040 Service Manual Download

Page: 124 / 131

Display codes other than trouble

Trouble codes

Sub code

Operation

—

Door open/DV unit uninstalled

—

Personal counter uninstalled/auditor code input waiting

—

Copy inhibit command is received from the host when installing PC/Modem.

(Key operator program)

The list below shows all key operator programs. These programs can be used only when the key operator code in inputted at the beginning.

Program

Code No.

Program name

Function

P10

Auditing Mode

Enables or disables the basic auditing mode, which controls access to copier.

P11

Number of Copies per Account

Displays the total number of copies made against account numbers.

P13

Resetting Account

Resets all audit accounts or selectively resets individual accounts.

P14

Account Number Control

Registers accounts, deletes accounts, changes an account number, or displays all
registered account numbers.

P16

Account Limit Setting

Sets the maximum number of copies which can be made against a registered account
number.

P18

Account Number Security

Guards against trial and error entering of audit account numbers.

P19

Key Operator Code Number Change

Changes the key operator code number.

P20

Auto Exposure Adjust

Lightens or darkens copies in the automatic exposure mode.

P21

Auto Power Shut-off Timer

Sets a time interval after which the copier automatically turns off.

P22

Toner Save Mode

Reduces toner consumption.

P23

Auto Clear Setting

Sets a time interval after which the copier returns to the initial settings.

P24

Add or Change Extra Preset Ratios

Adds or changes reduction and enlargement preset copy ratios.

P25

Setting a Maximum Number of Copies

Sets the maximum number of copies that can be selected.

P26

Initial Margin Shift Setting

Sets the initial margin shift values.

P27

Erase Width Adjustment

Sets the amount of the erase area.

P28

Initial Status Setting

Sets the copier’s initial settings in the ready condition.

P29

Total Copy Count

Recalls the total copy counts of the copier, document feeder, duplex module, and stapler.

P31

Preheat Mode Setting

Sets the time that elapses before the copier enters the preheat mode after copying is
completed.

P42

Right/Left Shift Direction Selection

Determines whether shift direction change is to be allowed.

P43

Erase Mode Initial Setting

Selects the erase mode’s initial setting.

P45

Message Time Setting

Sets the length of time that messages are displayed.

P46

Require Key Operator Code

Prevents the copier from being started by people other than key operator.

P47

Stream Feeding Mode

Enables the stream feeding mode for copying from an optional document feeder.

P70

Disabling of Auto Paper Selection

Prevents automatic paper selection when using the ORIGINAL SIZE ENTER key or
copying from an optional document feeder.

P71

Disabling of Auto Tray Switching

Prevents automatic switching between the paper trays.

P72

Prohibiting of Manual Feed Tray in
Duplex Copy

Prohibits the use of the manual feed tray during duplex copying. (Duplex copying can be
performed when an optional duplex module is installed.)

P73

Disabling Deletion of Job Programs

Prevents stored programs from being replaced or deleted.

P74

Disabling of Document Feeder

Prevents the use of an optional document feeder when it malfunctions.

P75

Disabling of Duplex Copying

Temporarily prevents the optional duplex system from operating when it malfunctions.
Allows the use of the copier but not the duplex system.

P76

Disabling of Stapler

Prevents damage to the stapler while awaiting repair service. (Staple sorters are
optional.)

P77

Disabling of Covers

Prevents the selection of COVERS mode.
(The COVERS mode can be used when an optional document feeder is installed.)

P83

Disabling of PC/Modem Access

Provides or prevents access to key operator programs through a PC/modem without key
operator code entry.
(Remote access to key operator programs can be performed only when a computer or
other equipment is connected to the copier directly or through a telephone line.)

P90

Display the List of All P Codes

Sequentially displays all available programs.

8 – 18