Phase
washer
wheel
Figure
Install the pulley and the cassette loading belt on
the worm shaft assembly. Couple the clutch to
the clutch lever. And mount them together in
the cassette housing frame
Note:
Keep in mind that the clutch switching lever
should be in the correct position.
The
mechanism might malfunction if the lever is
slightly out of position. (See page
Cassette loading belt
Cassette housing frame
arm
Tighten one B tight screw.
Note:
Do not over-tighten the B tight screw (no more
than
kg-cm), because the lower threads
of the screw hole at the resin-made boss can be
broken.
Place the start sensor
on the cassette
housing frame
Note:
Check that the switch connectors (No.
are
in the cassette switch mounting hole.
Finally resolder the cassette switch connector to
the start sensor
-Cassette
housing
frame(R)
shaft bear
REASSEMBLY OF DRIVE GEAR
W orm wheel
square hole
Drive gear spring
spring
Drive gear arm
1
Drive gear arm
Worm wheel
Figure
Attach the worm bracket to the worm shaft
assembly. Place them onto the boss on the
cassette housing frame
Note:
Insert before screwing into and
Cassette housing frame
Drive gear
spring
spring-shaft
(Drive gear bottom view)
Figure
Pass the tip of the drive gear spring
through the square hole of the drive gear
to
hook the spring in position.
Hook one end of the reciprocating spring to
the catch of the drive gear
Hook the other end
of the reciprocating
spring to the catch of the worm wheel.
Insert the pillar of the drive gear
into the
square hole of the worm wheel. Turn the worm
wheel somewhat counterclockwise for insertion
of the worm wheel to the drive gear
because
the reciprocating spring is at work.
Figure l-l
Summary of Contents for VT-3418X
