l
Checking the brake torque at the take-up side
REPLACEMENT OF MAIN BRAKE
Remove the reel belt and the reel block
(Full
Flat Cable).
Remove the cut washer off the brake shifter.
Unscrew the four screws
and then the
up reel retainer.
Remove the reel block assembly
downward.
Remove the cut washer first and then the reel
pulley.
Unscrew the two screws
and detach the idler
assembly.
Unhook the back tension lever spring and
remove
the back
tension lever
(Undo the
hook under the reel chassis.)
Open the shifter latch
and remove the brake
shifter assembly
Release the reel disk catchesand
then remove
the left and right reel disk assemblies and
Finally remove the main brake levers
and the
main brake spring
.
chassis
Figure
Remove the cassette housing control assembly.
Slowly rotate the torque gauge in the clockwise
direction and counterclockwise
direction of the take-up brake so that the reel
disk and the indicator of the torque gauge
rotate at an equal rate. Check that the values
are within the range of
direction
to
direction
to
and
that the brake torque in the
direction is at
least twice as high as that in the
direction.
Adjustment of the brake torque at the supply
side and the take-up side
If the supply or take-up brake torque is outside
the range, clean the supply or take-up reel disk
break lever felt, then recheck the torque.
If the supply or take-up brake torque is still
outside the range, replace the main brake or the
main brake spring.
Figure
Note:
When the main brake is replaced, perform the
height checking and adjustment (see page
and
the brake torque checking (see page
Summary of Contents for VT-3418X
