I
Removal
Loading mot
Figure
Unsolder the leads
from the loading motor.
Unlock the left and right catches
of the cam
switch off the loading block. Take out the cam
switch and loading block
(See Figure
marks
block
Pull up the cam switch pressing
the catches. Remove the cam switch
Catches of cam switch
together with the loading
Figure
Take out the loading belt
Pry up the back end of the loading motor with a
screw driver or the like as in Figure
and take
out the motor.
Motor label
Q
Loading belt
a
screwdriver or
the
like here. Pry UP the
back end of the
loading motor and
take out the motor.
Figure
cam
Set the loading block
and the cam switch in
position.
Resolder the leads to the loading motor.
Finally place the loading block (See page
Attach the loading belt.
Figure
mm
Note:
When press-fitting the loading
motor pulley, keep the pressure
less than 5 kg, and the gap
between the motor and pulley
should be
mm.
Figure
REPLACEMENT OF MASTER CAM
l
Removal
Remove the E ring
Remove the pinch roller lever
Pull out the master cam upward.
Pinch roller lever
Pinch roller lever
I
Master cam
Bottom side of
master
cam
l
Reassembly
Remove the loading motor, and mount a new
loading motor as in Figure
lever cam follower
(Place the relay shifter
lever to the unloading position.)
Place the loading motor so that its label is visible
as
in Figure
Make sure that the
screw hole at the motor shaft, protuberance *on
the
block, and the motor’s back end
marked with the arrow are mated with each
other.
brake lever cam follower
Figure
Summary of Contents for VT-3418X
