I
I
ADJUSTMENT
TV ELECTRICAL CIRCUITRY
ADJUSTMENT
I
Adjusting Conditions
Adjusting Procedures
CRT Cut-off Adjustment
Adjusting Point
Cl
Red Bias control
Cl
Green Bias control
Blue Bias control
Screen control (a pat-t of
Green Drive control
Blue Drive control
Note:
Prior to this adjustment, warm up the unit with the
beam current of more than
I
for more than
minutes.
Receive “MONOSCOPE PATTERN” signal with
pattern generator.
Set Red bias control at
(O/l position.
Set Green bias control at
(O/l position.
Set Blue bias control at
(O/l position.
Set Green drive control at CENTER
position.
Set Blue drive control at CENTER
position.
Set the control at the “NORMAL” position that
Contrast is MAX
is CENTER
an
Brightness is CENTER
using control, “A” and
keys.
Set the Screen control at
(O/l position.
Turn on
(Service switch) at the horizontal
line position.
Connect the oscilloscope to
(Red Cathode).
Sub-Contrast Adjustment
Adjusting Point
Sub-Contrast control
Note:
Prior to this adjustment, warm up the unit with the
beam current of more than
I
for more than
minutes.
Receive “MONOSCOPE PATTERN” signal with
pattern generator.
Set the Contrast and Brightness controls at MAX
position.
Connect DC
to
and
(Full scale: 3
Adjust the Sub-Brightness control
so that
the blanking pulse on oscilloscope is
Slowly turn the Screen control clockwise and stop
it where the horizontal raster appears slightly, in
one of the three
Carefully adjust the Bias controls of the other two
the horizontal raster becomes white.
Turn the Screen control counterclockwise until
the horizontal raster disappears, and stop it.
Adjust Sub-Contrast control so that the beam
current becomes
1
8
Summary of Contents for VT-3418X
