background image

15

Single item entries

Department entries

For a merchandise classification, the cash register provides a maximum of 99 departments.  To the
departments, group attributes such as taxable status are applied to items when they are entered.

• When using the department keys (for department 1 to 40)

For department 1 to 20, enter a unit price and press a department key.  If you use a programmed unit price,
press a department key only.
For department 21 to 40, enter a unit price, press the 

D

key and press a department key.  If you use a

programmed unit price, press the 

D

key and press a department key.

*

1

Less than the programmed upper limit amounts
When zero is entered, only the sales quantity is
added.

*

For the departments 21 through 40, press the
department shift key.

Please note if you press the same key after using the 

D

key, it acts as a repeat entry.  For

example, when you register an item of dept. 21 using the 

D

key and then an item of dept. 1

using the preset unit price,  you should use the department code entry key described below for the
dept. 1 item.  If you just press the 

¡

key to register dept. 1 item, it will act as a repeat entry of

dept. 21 item. 

• When using the department code entry key

Enter a department (dept.) code and press the 

d

key, then enter a unit price and press the 

d

key again.  If

the dept. code is programmed to preset price entry style and a unit price is preset, the cash register will finish
its registration operation.

*

1

Less than the programmed upper limit
amounts
When zero is entered, only the sales
quantity is added.

*

2

After you enter a unit price, you can
press the 

q

key instead of the 

d

key.

PLU/sub-department entries

For another merchandise classification, the cash register provides a maximum of 7000* PLUs/sub-departments.
PLUs are used to call up preset prices by a code entry.  Sub-departments are used to classify merchandise into
smaller groups under the departments.  Every PLU and sub-department has a code from 1 to 7000, and should
belong to a department to obtain attributes of that department.
The cash register is pre-programmed to PLU mode and zero for unit price.  To use PLU entries, their preset unit
prices should be previously programmed.  (Refer to page 38.)
To use sub-department entries, change to sub-department mode for the PLU codes.
*A total of 7000 codes, including UPC codes, can be programmed.

• PLU entries

PLU code

(1 to 7000)

o

Dept. code

(1 to 99)

Unit price *

1

(max. 7 digits)

When using a programmed unit price

(In case only preset price entry is allowed.)

d

d

*

2

Department key

Unit price *

1

(max. 7 digits)

When using a programmed unit price

D

*

2

Item Entries

3

 A506_2 FOR THE OPERATOR  09.10.14 9:26 AM  Page 15

Summary of Contents for XE-A506





































































































































Reviews: