6. Changing the system mode
The video input system mode is set to AUTO at the factory,
but it can be changed to a different mode.
1) Press the MENU button. The menu will appear on the
screen.
2) Press the ADJUSTMENT
ƒ
/
∂
buttons until the
©
mark is
set to “SYSTEM”.
Press the MENU button to display the system menu.
3) Press the ADJUSTMENT
ƒ
/
∂
buttons until the
©
mark
matches the video system desired and then press the
MENU button to set the system.
Note:
• In AUTO mode, “PAL”, “SECAM”, “NTSC4.43” or
“NTSC3.58” is displayed on the screen for a few seconds
when the mode is changed with the INPUT SELECT button.
VIDEO
PA L
VIDEO
N 4 4 3
VIDEO
N 3 5 8
VIDEO
S E C A M
PAL
SECAM
NTSC 3.58
NTSC 4.43
S Y S T E M
• S E C A M
• N 4 . 4 3
: S E L . M E N U : E N D
• P A L
A U T O
• N 3 . 5 8
On-Screen Display
X G - E 6 9 0 U B ( E ) / p p . 1 3 - 1 6
G. K . A s s o c i a t e s , To k y o
7. Select input.
Press the INPUT SELECT button to switch the picture input.
When you press the button, the current input mode is
displayed for about 4 seconds. If you press the button again
while the input mode is displayed, the mode changes as
shown on the left.
Confirm the selected input terminal, then press the INPUT
SELECT button.
Notes:
• In VIDEO mode, the system being received will be indicated
below the “VIDEO” display.
• When selecting RGB mode, the resolution being displayed
will be indicated under “RGB,” as shown on the left. (Refer
to second example when connecting to Mac display.)
• When no signal is being received, “NO SIGNAL” will be
displayed. When receiving a signal the projector is not
preset to receive, “NON REG.” will be displayed. (This
display function does not operate in Video mode.)
8. Adjust the volume.
Press the Volume Up-Down buttons on the projector or on the
remote control to adjust the volumes.
MUTE
• Press the MUTE button to temporarily turn off the sound.
• Press the button once again to turn the sound back on.
9. Turning off the power from the projector
or remote control
The power can be temporarily turned off by pressing the
POWER button on either the projector or remote control.
Note:
• When the MAIN POWER is off on the projector set, the
power cannot be turned on from the remote control.
After the POWER indicator lights red and the cooling fan runs
for 90 seconds, the power will turn off, and the projector will
return to STANDBY mode.
The power can be turned on again either from the projector or
remote control. When the power is turned on, the POWER
indicator and LAMP REPLACEMENT indicator light green.
For viewing the picture
from a video source
connected to:
VIDEO INPUT or
S-VIDEO INPUT
COMPUTER RGB
VIDEO
N 3 5 8
RGB
8 0 0 x 6 0 0
6 0 H z
RGB
6 4 0 x 4 8 0
RGB
6 4 0 x 4 8 0
RGB
8 3 2 x 6 2 4
KHz
KHz
97
34 .
35
Mac
RGB
8 0 0 x 6 0 0
6 0 H z
RGB
6 4 0 x 4 8 0
6 0 H z
VO L U M E
The number of displayed segments
increases or decreases as the volume
is raised or lowered.
M U T E
POWER
LAMP
TEMP.
E-15
1 9 9 8 / 5 / 2 1
