background image

.                                                                                          .

.

.

25

4

TABLE OF CONTENTS

O. ANTI CAR- JACKING..............................................................13-14

    Active Car Jacking

    Passive Anti Car Jacking

    Trigger The Anti Car Jacking Mode

    Override The System To Turn Off Anti Car Jacking

P.  SYSTEM’S TRIGGER CHECK ........................................................15

Q. SYSTEM’S STATUS CHECK ..........................................................15

R. DRIVER PAGING........................................................................15

S. DOME LIGHT CONVENIENCE DELAY & SUPERVISION......................15

T.  IGNITION CONTROL THE DOOR LOCK/UNLOCK .............................16

U. TRUNK RELEASE (CHANNEL 3) OUTPUT........................................16

V.  CHANNEL 4 TIMER CONTROL OUTPUT..........................................16

W. POWER ON MEMORY:.................................................................16

A. BATTERY REPLACEMENT.............................................................17

B. THE REMOTE LCD ICONS WITH FUNCTION...............................17-18

C. PROGRAMMING OF THE LCD REMOTE TRANSCEIVER ................19-21

    Screen Lamp ON

    Power Save Mode

    Clear The Flash Icon and Melody Sound

    Stop The Melody Sound.

    Button Lock

   Vibration / Melody Mode

    Enable / Disable Bi Sound While Pressing Button:

    Low Battery Indication.

Set Up Fixed Count Down Timer

  Out Of The Range Check

D. TIMER SETTING ...................................................................22-24

  Timer Setting.

  Alert Alarm Timer Setting

    Count Down Timer Setting

Summary of Contents for CS-500S















Reviews: