background image

05-10ET13-0B

Page 8

7. dooR And SolId end PAnel InSTAllATIon

A.

 Hold end panel at the top center with white inner surface facing inside of the shelter. Wrap the edges of the   

     fabric panel around the end rib.

B.

 Disconnect top rail from the end rib. Pass the top cross rail through the gap in the fabric, in between the  

     

     webbing and rib frame. Re-attach top cross rail to end rib. 

Repeat Step B for side cross rails.

C. 

If this connection has the wind brace on it remove the wind brace end before pulling the side rail.       

     Replace the cross rail and wind brace. Replace the bolt and tighten. Repeat this on the other side.

D.

 At the bottom, where the webbing exits the pocket on each side of end panel, pull webbing to remove the    

     slack. 

Be careful not to pull the webbing through the other side of the webbing pocket. 

E.

 Insert the “S”- Hook on ratchet into hole on the leg bend. Insert the webbing into the spindle of the ratchet    

     and pull tight. Wind the ratchet so that the webbing overlaps itself. 

     Position the end panel so that it is centered on the building before fully tightening the end panel. 

F.

 Tighten ratchets, alternating from one side to the other, until the end panel is centered and tight.

    Zipper Door Panels: Zippers must be closed when tightening end panel.

Thread Webbing Into Ratchet

SIde cRoSS

RAIlS

WeBBInG

zIPPeRS

ToP cRoSS

RAIl

WRAP end

PAnel edGeS

To InSIde oF 

FRAme

WRAP end PAnel edGeS To InSIde oF FRAme

InSIde VIeW oF end RIB

SIde VIeW oF end RIB

coVeR

RAIl

Webbing and Ratchets Securing End Panel

Summary of Contents for 10' x 8' x 8' Peak Style Shelter










Reviews: