background image

                                                                                                                              Operation  instruction 

 

9

 

Warranty period"), at its option either(a) repair your product with new or refurbished parts, or 

(b) replace it with a new of a refurbished product. The decision to repair or replace will be 

made by the warrantor. 

During the "Labor" Limited Warranty period there will be no charge for labor.   

During the "Parts" warranty period, there will be no charge for parts. You must mail-in your 

product during the warranty period. This Limited Warranty is extended only to the original 

purchaser and only covers product purchased as new. A purchase receipt or other proof of 

original purchase date is required for Limited Warranty service. 

 

Mail-In Service

 

When shipping the unit carefully pack and send it prepaid, adequately insured and preferably 

in the original carton. Include a letter detailing the complaint and provide a day time phone 

and/or email address where you can be reached. 

 

 

 

 

LIMITED WARRANTY LIMITS AND EXCLUSIONS 

1)

 

This Limited Warranty ONLY COVERS failures due to defects in materials or 

workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The 

Limited Warranty ALSO DOES NOT COVER damages which occurred in shipment, or 

failures which are caused by products not supplied by warrantor,or failures which result from 

accidents,misuse,abuse,neglect, mishandling, misapplication, alteration, faulty installation, 

set-up adjustments, misadjustment of consumer controls, improper maintenance, power line 

surge, lightning damage, modification, or service by anyone other than a Factory Service 

center or other Authorized Servicer, or damage that is attributable to acts of God. 

2)

 

THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER "LIMITED 

WARRANTY COVERAGE".THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR 

CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR 

ARISING OUT OF ANY BREACH OF THIS WARRNTY. (As examples, this excludes 

damages for lost time, cost of having someone remove or re-install an installed unit if 

applicable, travel to and from the service, loss of or damage to media or images, data or other 

recorded content. The items listed are not exclusive, but are for illustration only.) 

3)

 

PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED 

WARRANTY, ARE YOUR RESPONSIBILITY. 

 

Summary of Contents for LM-EHU100










Reviews: