3
together and fed to both amplifiers. Please note that
the volume setting can only be controlled by the
‘R’ channel volume control.
12VDC Trigger In and Out
The Trigger output is 12V at a maximum of 100mA.
This can be used to drive a relay operated AC out-
let or other 12V triggered devices. The 12V volt
trigger input is used to activate the amplifier inde-
pendently from the auto turn on sensing circuit, in
which case the delay, video and audio sensing are
bypassed.
Music and Video Trigger
Apart from the 12V Trigger you can also use the
Audio and Video signal (fed through the ‘Line In’
connectors or the ‘Speaker Level Input’ connec-
tors) to ‘Wake-up’ your 2/100A from its ‘Standby’
mode. By receiving any one of these three signals
the 2/100A will ‘Wake-up’ automatically and the
LED will immediately turn to full brightness. When
the 2/100A is being ‘Triggered’ by a music or video
source you will notice that once the music stops
playing OR whenever the 2/100A has received no
music signal for its ‘Pre-set’ period (see note be-
low) it will enter its ‘Standby’ mode..meaning that
the amplifier is effectively ‘Put to sleep’ to con-
serve power and the LED will dim to half bright-
ness. The ‘Video’ trigger is paralleled with the ‘Mu-
sic’ trigger so they both have the same level of pri-
ority.
Auto Time Off
The 2/100A can be ‘Pre-set’ for automatic time off
for any period between 30 seconds to ten minutes
by setting the control between ‘1’ and ‘4’. There-
after, if the amplifier has received no music or video
signal for its predetermined time it will automati-
cally go into its standby mode. This feature can be
‘defeated’ by turning the knob to between positions
#`4 and # 5. Under this setting the 2/100A can
only be turned off from the Power Switch and it
will not enter into either its ‘Standby’ or ‘wake-up’
mode.
It is important to note that the 2/100A is designed
to work with a maximum of two pairs of 8 ohm
speakers or one pair of 4 ohm speakers. Please
consult your dealer about the impedance of any
speakers that you intend to use with your 2/100A
because the warranty will be invalidated if the 2/
100A is used outside of the parameters outlined
in this paragraph.
Five Year Limited Warranty
Subject to the terms and conditions stated be-
low, Sherbourn Technologies, Inc. (Sherbourn)
warrants to the original owner that this Product shall
be free from defects in workmanship or materials
for a term of five (5) years from its date of pur-
chase from an Authorized Sherbourn Dealer. Trans-
fer of this product by its original owner (the
‘Owner’) will automatically terminate this War-
ranty regardless of when occurring.
In the event of any defect covered by this war-
ranty, Sherbourn shall provide all parts, materials,
and labor necessary to restore the Product to its
original specifications, and shall return the Prod-
uct to its owner at Sherbourn’s expense. In the al-
ternative, Sherbourn may at its sole option either
replace the Product without charge, or if its replace-
ment is not commercially practicable or repair or
replacement cannot be accomplished within a rea-
sonable time, Sherbourn may refund the purchase
price of the Product, subject where appropriate to
reasonable depreciation for actual use in accor-
dance with applicable laws, in full satisfaction of
its warranty obligations.
Sherbourn’s sole obligation under this warranty
shall be to repair or replace the product, or at its
option refund the purchase price, as provided for
hereinabove. Sherbourn does not warrant
against, nor shall it be liable for, any of the fol-
lowing: removal or installation charges, shipping
expenses to its authorized service facility, loss of
use, property damage of any kind, or other inci-
dental or consequential damage or losses of any
kind.
Note: Some states do not allow exclusion or limi-
