background image

13

Warranty

Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts.  A one-year 

warranty is provided on all electrical components.  The above limited warranties are extended only to the 

original purchaser.

There is no warranty on the following parts:

● Glass window

● Fiberglass rope gaskets

● refractory material

● burn pot liner

● paint

● enamel finish or gold plating where it applies

**NOTE: 

The paint on the brick firebox lining may peel. This is due to the extreme conditions 

applied to the paint and is in no way covered under warranty.

WHEN FILING A WARRANTY CLAIM PLEASE COMPLETE THE FOLLOWING INFORMATION 

ON AN OFFICIAL WARRANTY CLAIM FORM:

TO THE DEALER:

-  Name and address of dealer,

-  Date of purchase

-  Name, address and telephone number of purchaser

-  Name, address and telephone number of installer

-  Date of installation, and

-  Serial number of the appliance

Ensure that you specify the nature of the complaint, defect, periodical malfunction, etc.

TO THE DISTRIBUTOR:

-   Sign and verify that work and information are correct.

-   Description and part # of any parts replaced.

The limited warranty covers defects in materials and workmanship as long as the products has been 

installed according to the manual’s instruction.  If the product is damaged or broken as a result of 

mishandling or misuse, the warranty does not apply.  Removal and re-installation costs are not covered 

under this warranty.

It is the manufacturer’s option whether to repair or replace the appliance. The shipping cost to and 

from the factory is to be paid by the consumer.  All warranties by the manufacturer are set forth herein 

and no claim shall be made against the manufacturer on any oral warranty or representation.

The manufacturer assumes no responsibility for damage caused by household power fluctuations or 

power surges.

Under Warranty

For the do-it-yourself Individual

The consumer should be aware that the pellet appliance needs setting using tools that he/she might 

not have. It is recommended that you have a qualified installer install your pellet appliance

Sherwood Industries Ltd. reserves the right to make changes without any notice.

Summary of Contents for Enviro Bern















Reviews: