background image

4

Avoid long-term  operation in very 

hot or very cold weather.

Make sure bystanders or  observers 

outside the 15 meters  “danger zone” 

wear eye protection.

Be extremely careful of 

slippery terrain, especially 

during rainy weather.

If contact is made with a hard 

object, stop the engine and  

inspect the cutting attachment  

for damage.

When operating in rocky terrain or near 

electric wires or fences, use extreme 

caution to avoid contacting such items 

with the cutting attachment.

Be constantly alert for objects and 

debris that could be thrown either 

from the rotating cutting attachment 

or bounced from a hard surface.

Reduce the risk of  bystanders being 

struck  by flying debris. Make  sure no 

one is  within 15 meters—that’s about 

16 paces—of an operating  attachment.

IMPORTANT!

Safety and Information Labels: Make sure all safety and 

information labels are undamaged, readable and up to 

date. Immediately replace damaged or missing labels. 
New labels are available through your local authorized 

Shindaiwa dealer.

Safety Labels

SHINDAIWA OWNER’S/

OPERATOR’S MANUAL

MULTIPURPOSE

EDGER TOOL

Always wear eye and

ear protection when

operating this machine!

WARNING!

To minimize the risk of

injury to yourself and

others, read this manual

and familiarize yourself

with its contents.

WARNING!

1439

1440

65010-94010_MLE230_07LP

11/21/01, 11:19 AM

1

50 FEET

(15m)

KEEP BYSTANDERS AWAY

AT LEAST 50 FEET (15m)

BEWARE OF THROWN OR
RICHOCHETED OBJECTS

KEEP AWAY FROM

ROTATING BLADE

Shindaiwa Inc.

65010-94010_MLE230_07LP

11/21/01, 11:19 AM

4

Summary of Contents for 65010













Reviews:

Related manuals for 65010