background image

13

Shoulder strap 

required for use 

with Brushcutters

Operation

IMPORTANT!

Adjust the shoulder strap so the shoul-

der pad rests comfortably on the off-

side shoulder and the cutting path of  

the cutting attachment is parallel to 

the ground. Make sure all hooks and 

adjustment devices are secure.

WARNING!

  Always wear a shoulder 

strap or harness when operating 

this unit. Using a harness with a 

brushcutter allows you to main-

tain proper control of the unit and 

reduces fatigue during extended 

operation.

Shoulder strap

1.  Hook the strap hook to the hanger 

on the outer tube.

2.  Wear the shoulder strap so that the 

hook stays at your right hand side.

3.  Adjust the length of the shoulder 

strap so that you can hold and oper-

ate the machine comfortably.

NOTE:

Using a shoulder strap when operat-

ing this unit with a blade allows you 

to maintain proper control of the unit 

and reduces fatigue during extended 

operation.

WARNING!

Moving parts can amputate fingers or cause severe injuries.  Keep hands, clothing and loose objects away from 

all openings.  Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop 

before removing obstructions, clearing debris, or servicing unit. 

WARNING!

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas.  Breathing CO can cause uncon-

sciousness, serious injury, or death. Exhaust can cause serious burns.  ALWAYS position unit so that exhaust is directed 

away from your face and body..  

WARNING!

Operation of this equipment may create sparks that can start fires. This unit is equipped with a spark arrestor 

to prevent discharge of hot particles from the engine. Metal blade use also can create sparks if the blade strikes rocks, 

metal, or other hard objects. Contact local fire authorities for laws or regulations regarding fire prevention requirements.  

Your Shindaiwa unit may be equipped 

with one of several Shindaiwa trimmer 

head models, each with features for spe-

cific applications and/or operational 

requirements.

Cutting grass with a trimmer head

NOTE:

For proper operation, always refer to 

the instructions accompanying the trim-

mer head being used.

CAUTION! 

Operation at low rpm can lead to 

premature clutch failure.

Engine Operating Speeds

Operate at full throttle while cutting 

grass.

Summary of Contents for C282

































Reviews: