background image

14

Limited Lifetime Warranty

Ever y Shinola Runwell Turntable is guaranteed for life against manufacturing defects under the terms and 
conditions of our Limited Lifetime Warrant y as described herein. Any defective component (excluding the 
car tridge, slipmat and belt) will be repaired or replaced by Shinola . If we cannot repair your turntable and 
the exact model is not available for replacement , a model of equal value will be provided. A copy of the 
receipt or your completed online product registration is required as proof of purchase. A check or money 
order payable to Shinola /Detroit , LLC in the amount of $50.00 will be required as a ser vice and handling 
fee for all warrant y ser vices. This fee is subject to change.

T H I S  L I M I T E D  WA R R A N T Y  D O E S  N OT  COV E R  A N Y  DA M AG E  O R  O P E R AT I O N A L  FA I LU R E 
C AU S E D  BY:

Any thing not within Shinola’s control. Specifically, this warrant y shall not cover damage caused by 
improper handling, use or care on the par t of the owner or any third par t y (other than any authorized 
Shinola sales or ser vice personnel). 

An accident of any kind, negligence, or any intentional act by the owner or any third par t y.

A D D I T I O N A L  E XC LU S I O N S;  VO I DA B I L I T Y

This Limited Warrant y shall not apply to or cover any damage to or failure of the car tridge (including 
st ylus), slipmat or belt provided with this purchase. Fur ther, this Limited Warrant y shall not apply and shall 
be void with respect to (i) turntables with serial numbers (located on the plat ter and back plate) that have 
been defaced or altered or (ii) any repair, alteration, or modification made by persons other than Shinola 
personnel or a Shinola authorized dealer or ser vice provider. 

The Limited Warranty described herein is the sole and exclusive warranty for this product and is 

Summary of Contents for RUNWELL





















Reviews: