Shop fox W1715 Owner'S Manual Download

Page: 8 / 48

-6-

Model W1715 (For Machines Mfd. Since 2/19)

Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,.

MAY.result.in.minor.or.moderate.injury.

Indicates.an.imminently.hazardous.situation.which,.if.not.avoided,.

WILL.result.in.death.or.serious.injury.

Indicates.a.potentially.hazardous.situation.which,.if.not.avoided,.

COULD.result.in.death.or.serious.injury.

This.symbol.is.used.to.alert.the.user.to.useful.information.about.

proper.operation.of.the.equipment.or.a.situation.that.may.cause.

damage.to.the.machinery.

NOTICE

SAFETY

OWNER’S.MANUAL..

Read and understand this

owner’s manual BEFORE using machine.

TRAINED.OPERATORS.ONLY..

Untrained operators

have a higher risk of being hurt or killed. Only

allow trained/supervised people to use this

machine. When machine is not being used,

disconnect power, remove switch keys, or

lock-out machine to prevent unauthorized

use—especially around children. Make

workshop kid proof!

DANGEROUS.ENVIRONMENTS..

Do not use

machinery in areas that are wet, cluttered,

or have poor lighting. Operating machinery

in these areas greatly increases the risk of

accidents and injury.

MENTAL.ALERTNESS.REQUIRED..

Full mental

alertness is required for safe operation of

machinery. Never operate under the influence

of drugs or alcohol, when tired, or when

distracted.

ELECTRICAL.EQUIPMENT.INJURY.RISKS..

You can

be shocked, burned, or killed by touching live

electrical components or improperly grounded

machinery. To reduce this risk, only allow an

electrician or qualified service personnel to

do electrical installation or repair work, and

always disconnect power before accessing or

exposing electrical equipment.

DISCONNECT.POWER.FIRST..

Always disconnect

machine from power supply BEFORE making

adjustments, changing tooling, or servicing

machine. This eliminates the risk of injury

from unintended startup or contact with live

electrical components.

EYE.PROTECTION..

Always wear ANSI-approved

safety glasses or a face shield when operating

or observing machinery to reduce the risk of

eye injury or blindness from flying particles.

Everyday eyeglasses are not approved safety

glasses.

Standard.Machinery.Safety.Instructions

For.Your.Own.Safety,

Read.Manual.Before.Operating.Machine

The. purpose. of. safety. symbols. is. to. attract. your. attention. to. possible. hazardous. conditions.. This.

manual.uses.a.series.of.symbols.and.signal.words.intended.to.convey.the.level.of.importance.of.the.

safety.messages..The.progression.of.symbols.is.described.below..Remember.that.safety.messages.by.

themselves.do.not.eliminate.danger.and.are.not.a.substitute.for.proper.accident.prevention.mea-

sures—this.responsibility.is.ultimately.up.to.the.operator!

SAFETY

Standard.Machinery.Safety.Instructions

Summary of Contents for W1715

















































Search results

Summary of Contents for W1715

Reviews:

Related manuals for W1715

Brands by name

Popular brands

Shop fox W1715, Owner'S Manual

Search results

Summary of Contents for W1715

Reviews:

Related manuals for W1715

Brands by name

Popular brands