background image

 
 

LIMITED WARRANTY 

 

 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

SHOW PRO INDUSTRIES 

P.O. Box 1235, Springtown, TX  76082 / (817)523-4055 / (817)220-5117 fax 

email: showpro@flash.net / www.procutter.com

 

The  following  warranty  is  in  lieu  of  all 
other  warranties,  expressed,  implied  or 
statutory, including but not limited to any 
implied  warranty  of  merchantability  or 
fitness for a particular purpose. 

All  new  products  sold  by  Show  Pro  Industries  are  warranted 
against  defects  in  material  and  workmanship  for  two  (2)  years 
from  the  date  of  original  purchase.    During  the  warranty  period, 
Show  Pro  Industries  will  repair,  or  at  its  option  replace  without 
charge, any SPI product (excluding normal wear items), providing 
it is returned to the factory, shipping prepaid, and is proven to be 
defective during the subsequent factory inspection.  The warranty 
period  for  products  repaired  after  expiration  of  new  product 
warranty,  as  stated  above,  is  limited  to  the  repair  portion  and  is 
valid  for  90  days  from  date  of  reshipment  to  customer.    All 
warranties,  expressed  or  implied,  are  void  if  product  is  damaged 
by  accident,  misuse  or  modification  in  the  absence  of  written 
authority from Show Pro Industries. 

 
 

Summary of Contents for PRO CUTTER 1502















Reviews: