background image

 

 

 

13 

 

  

 

 

PSA-16A3C 

Product code: 50660 

6.

 

Troubleshooting 

This troubleshooting guide contains solutions to problems which can be carried out by an ordinary 
person. The device does not contain user-serviceable parts. 

Unauthorized modifications to the device will render the warranty void. Such modifications may result in 
injuries and material damage. 

Refer servicing to instructed or skilled persons. Contact your Highlite International dealer in case the 
solution is not described in the table. 

Problem 

Probable cause(s) 

Solution 

The device does not 
function at all 

No power to the device 

 

Check if power is switched on and 
cables are plugged in 

The main circuit breakers are in 
OFF position 

 

Check the total current load of the 
connected devices. 

 

Check if the external devices 
connected to the outputs are not 
damaged 

 

Move the main circuit breakers to ON 
position. 

7.

 

Maintenance 

 

Safety Instructions for Maintenance 

 

DANGER 
Electric shock caused by dangerous voltage inside
 

Disconnect power supply before servicing or cleaning. 

 

Preventive Maintenance 

 

Attention 
Before use, examine the device visually for any defects. 

Make sure that: 

 

All screws used for installing the device or parts of the device are tightly fastened and are not 
corroded. 

 

There are no deformations on housings, fixations and installation points. 

 

The power cables are not damaged and do not show any material fatigue. 

 

Basic Cleaning Instructions 

To clean the device, follow the steps below: 

 

Disconnect the device from the electrical power supply. 

 

Allow the device to cool down for 5 minutes. 

03)

 

Clean the device with a soft, lint-free cloth. 

 

 

Summary of Contents for PSA-16A3C

















Reviews: