background image

  

 

5

SHENZHEN SHUNXUN ELECTRONICS CO.,LTD

www.foxun.com

 

120m HDMI Extender over Ethernet, with RS232, POE, IR

4 bits DIP Switch:   

Use 4bits DIP switch to select 16 group ID(such as 0001,0010,0101 etc,) 
Default RX unicast IP address is 192.168.168.56, it can be configured from webpage. 
RX Group IP address: 239.168.168. XXX (XXX is the value of bits[2:0]) 

 
User should configure the DIP switch within 10 seconds, firmware should reset the 
system 20 second after detecting the first change of DIP switch, and latch the new 
DIP switch value after reset.   
 
Application 1: 
Point to point configuration:     
 

1. Connect one HDMI Cable between the HDMI output port of source device and the HDMI input port of 
Transmitter unit     
2. Connect one HDMI Cable between the HDMI input port of display and the HDMI output port of Receiver 
unit.   
3. Connect one UTP Cat5e or better cables between the RJ45 port of Transmitter unit and RJ45 port of 
Receiver unit.   
4. Connect 5V DC power supplies to both Transmitter unit and Receiver unit.   
5. Power on the output device first and the source second.   
 

 

Please make sure power on the transmitter and receiver first, then power 

on the source! 
 
 
 
 
 
 
 
 
 
 
 
 

HDMI cable

RS232 cable

RS232 cable

IR-TX cable

IR-RX cable

DVD or STB remote

HDMI cable

HDMI Display

HDMI cable

HDMI Source

Transmitter

Receiver

Free rotate camera

PC

Summary of Contents for SX-EP25












Reviews: