background image

  

  

 

7

SHENZHEN SHUNXUN ELECTRONICS CO.,LTD

www.foxun.com

 

120m HDMI Extender over Ethernet, with RS232, POE, IR

Application 3: 

Many to Many network configuration: 

   

 
1. Connect one HDMI Cable between the HDMI output port of source device and the HDMI input port of 
Transmitter unit.   
2. Connect one HDMI Cable between the HDMI inpu port of display and the HDMI output port of Receiver 
unit.   
3. Connect one CAT5e or better cable between the RJ45 of each Transmitter unit and RJ45 port of 
Gigabit Ethernet switch hub.   
4. Connect over each RJ45 port of Gigabit Ethernet switch hub with RJ45 port of Receiver unit.   
5. Use DIP switch to select sources, User can select source channel by DIP switch setting on each 
transmitter unit and set up DIP switch on each receiver.    And select display devices for Receiver units 
via one remote control 

Important:  Please make sure power on the POE switch first , then power on the  

source !

 

Now, If you need display Source2 on TV1, then just set Group ID of RX1 0101,same as TX2: 0101 (refer 
to Diagram). 

1).Use 4-bit DIP switch to select 16 group ID (such as 0001, 0010, 0101 etc.) 

When you set up the group ID for each transmitter just like this : 

3).For example, when the devices are connection as below : 

Source (DVD2) - TX (TX2) - Gigabit Switch - RX(RX2)- TV2 
Source (DVD3) - TX (TX3) - Gigabit Switch - RX(RX3)- TV3 

Source( DVD1) - TX (TX1) - Gigabit Switch - RX(RX1)- TV1 

2).Change group ID easily to select the sources. 

 

How to use DIP switch: 

TX1 (0001)   
TX2 (0101)   
TX3 (0100) 

 

 

 

Summary of Contents for SX-EP25












Reviews: