180
EuroFID · Operating Instructions · 8011094 V2.3 · © SICK AG
Clearing Malfunctions
50
E x t _ S a m _ S t o e
S Y S T E M E R R O R
T h e r e i s a n
i n t e r f e r e n c e
d e t e c t e d a t t h e
i n t e r f e r e n c e
c o l l e c t o r .
An external malfunction
message is activated
on a control input
(
).
Measurement is
interrupted.
Disappears as soon
as the cause is
eliminated.
Check the input signal
source (status, current
signal).
Check the electrical
connection.
51
R e m o O u t _ P o w e
S Y S T E M E R R O R
P o w e r f a i l u r e . T h e
m e a s u r i n g w i l l b e
s t o p p e d .
52
H 2 l e a k m o n i t
S Y S T E M E R R O R
H 2 l e a k m o n i t o r i n g
s y s t e m r e p o r t s l e a k
i n H 2 s y s t e m .
The external leakage
monitoring device has
interrupted the fuel gas
supply. Measurement is
interrupted.
Disappears as soon
as the cause is
eliminated.
Pay attention to the
explosion hazard and
implement the safety
measures specified for this
situation.
Check the condition/
displays of the leakage
monitoring device.
If necessary look for and
eliminate the leak.
54
S e r v i c e - I V L
S E R V I C E R E Q U I R E M E N T
T h e s e r v i c e i n t e r v a l
h a s r u n o u t . T h e
s y s t e m m u s t b e
s e r v i c e d .
Informative note; the
function of the device is
not affected as a result.
–
The maintenance
interval can be
programmed in the
“Expert level” sub-
menu (not described in
this document) and
runs with the hours of
operation.
The message is
reset manually on
the “Expert level”.
Notify the manufacturer's
after-sales service to have
preventative maintenance
work carried out on the
device.
56
D e t e O u t _ 3 0 0 V
S Y S T E M E R R O R
F I D d e t e c t o r v o l t a g e
i s t o o l o w .
Malfunction in the
measuring system: The
detector voltage is
lower than the
minimum value.
Measurement is
interrupted.
Disappears as soon
as the cause is
eliminated.
Check whether the current
mains voltage is too low
(permissible value
).
if this is not applicable:
Have the EuroFID serviced
by the after-sales service
of the manufacturer.
57
E l e c t . t o o h o t
S E R V I C E R E Q U I R E M E N T
T h e e l e c t r o n i c o f
t h e a n a l y z e r
a s s e m b l y i s t o o h o t .
Malfunction in the
measuring system: The
internal temperature is
too high. The measured
value is possibly
incorrect.
Disappears as soon
as the cause is
eliminated.
Check whether the
ambient temperature of
the analyzer unit is too
high (permissible range
).
if this is not applicable:
Have the EuroFID serviced
by the after-sales service
of the manufacturer.
58
E l e c t . t o o h o t
S Y S T E M E R R O R
T h e e l e c t r o n i c o f
t h e a n a l y z e r
a s s e m b l y i s t o o h o t .
59
I n S e r v i c e
S E R V I C E R E Q U I R E M E N T
T h e s y s t e m i s i n
s e r v i c e . T h e c o n t a c t
f o r m e a s u r e
r e a d i n e s s i s n o t
a c t i v e . T u r n o f f
s e r v i c e m o d e .
The “System in Service”
message is activated
(
Measurement is
interrupted.
Is shown as long as
the “System in
Service” is activated
(+ approx. ½ minute
after deactivation).
Terminate the “System in
Service” status – if this is
wanted and the current
conditions permit.
60
O f e n F l i m T e m p
S Y S T E M E R R O R
T h e t e m p e r a t u r e o f
t h e s e n s o r b l o c k i s
o u t o f t o l e r a n c e .
P l e a s e c h e c k s e n s o r
b l o c k a n d a m b i e n t
t e m p e r a t u r e .
The over-temperature
switch in the analyzer
unit has been triggered.
Measurement is
interrupted.
Disappears as soon
as the cause is
eliminated.
Reset the over-
temperature switch
If the
over-temperature
switch
is triggered once
more:
Have the EuroFID
serviced by the after-sales
service of the
manufacturer.
61
A n a l y z . h e a t .
S Y S T E M E R R O R
T h e h e a t i n g o f
s e n s o r b l o c k i s
d e f e c t i v e .
The temperature of the
sensor block in the
analyzer unit is too low
or was not reached in
the set running up time.
Measurement is
interrupted.
Disappears as soon
as the cause is
eliminated.
Check in the diagnosis
section whether this
message was triggered by
means of a random
transition status.
If this is not applicable:
Have the EuroFID serviced
by the after-sales service
of the manufacturer.
N Spontaneous message
Message text in the error archive
Significance
Duration of the
message
Countermeasures
Summary of Contents for EuroFID
