background image

2

Safety information

2.1

General safety notes

The safety locking device must be configured and operated correctly by qualified safety
personnel according to the machine requirements.

2.2

Intended use

When used in conjunction with a movable physical guard and the machine controller,
the safety locking device prevents the protective device from being opened while a dan‐
gerous machine function is being executed.

The safety locking device may only be used on the machine on which it was configured,
mounted, installed, and commissioned by qualified safety personnel in accordance with
these operating instructions.

Incorrect use, improper modification of or tampering with the safety locking device will
invalidate any warranty from SICK AG; in addition, any responsibility and liability of SICK
AG for damage and secondary damage caused by this is excluded.

NOTE

The safety locking device is also suitable for process protection.

2.3

Requirements for the qualification of personnel

The safety locking device must be configured, installed, connected, commissioned, and
serviced only by qualified safety personnel.

Project planning

For project planning, a person is considered competent when he/she has expertise and
experience in the selection and use of protective devices on machines and is familiar
with the relevant technical rules and national work safety regulations.

Mechanical mounting, electrical installation, and commissioning

For the task, a person is considered qualified when he/she has the expertise and expe‐
rience in the relevant field and is sufficiently familiar with the application of the protec‐
tive device on the machine to be able to assess whether it is in an operationally safe
state.

Operation and maintenance

For operation and maintenance, a person is considered competent when he/she has
the expertise and experience in the relevant field and is sufficiently familiar with the
application of the protective device on the machine and has been instructed by the
machine operator in its operation.

SAFETY INFORMATION 

2

8020548/ZT59ZT59/2019-01-17 | SICK

O P E R A T I N G   I N S T R U C T I O N S | i15 Lock

7

Subject to change without notice

Summary of Contents for i15 Lock





























Reviews: