2
4526
8
2020
-
SE IP 50
DECLARATION OF CONFORMITY
Sleipner Motor AS
P.O. Box 519, Arne Svendsensgt. 6-8
N-1612 Fredrikstad, Norway
Declare that this product with accompanying standard control systems complies with
the essential health and safety requirements according to:
DIRECTIVE 2013/53/EU
DIRECTIVE 2014/30/EU
DIRECTIVE 2014/35/EU
MC_0020
Bow Installation Instructions
Bow Installation Considerations and Precautions ..................... 3
Thruster Measurements .......................................................... 4
Thruster Specifications
.............................................................. 5
Technical Specifications
.......................................................... 5
Positioning of the tunnel / thruster ............................................. 6
Tunnel Length ............................................................................ 7
Tunnel installation in sailboats ................................................... 8
Water Deflection
........................................................................ 9
Tunnel ends ............................................................................. 10
Tunnel installation ............................................................. 11 - 12
Stern tunnel installation ........................................................... 13
Thruster Installation Instructions
Thruster Installation Considerations and Precautions ............. 14
Gear Leg & Motor Bracket Installation..................................... 15
Propeller Installation ................................................................ 16
Motor Installation ..................................................................... 17
Thruster Electrical Installation ................................................. 18
Electrical Specifications
.......................................................... 19
Control Panel Cable Installation ............................................. 20
Visual Wiring Diagram ............................................................ 21
Technical Wiring Diagram ....................................................... 22
Control Panel Installation ........................................................ 23
Pre-delivery Checklist .......................................................... 24
Spare Parts ............................................................................ 25
Warranty statement .............................................................. 25
Contents
EN
Products
SE50/140S-24IP - SE50 Tunnel thruster, 24V-IP
SE50/140S-12IP - SE50 Tunnel thruster, 12V-IP
MC_0031
Bow Installation Considerations and Precautions
EN
• The thruster must NOT be installed in compartments that require ignition proof electric equipment. If necessary, make a separate compartment.
(NB: Ignition Protected systems are tested to be installed in areas with possible explosive gases in accordance with ISO 8846)
• The electro motor will generate some carbon dust so any storage compartments must be separated from the thruster to prevent nearby items
becoming dusty/ dirty.
(NB: IP version motors generate dust but are enclosed.)
• When installing the thruster electro motor in small compartments, ensure the compartment is well ventilated to allow for cooling of the electro motor.
• If the height of the room you are installing the thruster is limited, the thruster can be installed horizontally or at any angle in-between.
- If the electro motor is positioned more than 30 degrees off vertical, it must be supported separately.
- Beware of keeping installation within advised measurements. No part of the propeller or gear house must be outside the tunnel.
• Do not install the thruster in a position where you need to cut a stiff ener/ stringer/ support that may jeopardise the hull integrity without checking with
the boat builder this can be done safely.
• The electro motor, components and cables must be mounted so they remain dry at all times.
• We advise painting the gear house and propellers with anti-fouling.
(NB: Do not paint the anodes, sealing, rubber fi ttings or propeller shafts)
• Do not fi nish the inside of the tunnel with a layer of gel-coat/ topcoat or similar. There is only room for a thin coat of primer and two layers of anti-
fouling between the tunnel and the props.
• Don’t install the electro motor close to easily fl ammable objects or equipment as it will reach over 100°C before the temperature switch is activated.
• Do not store items close to the thruster motor. Any loose items near the thruster motor is a potential fi re hazard and can cause undesired short-
circuiting.
MC_0267
NEVER
Disassemble any part of the Ignition Protected stern thruster assembly. Tampering with the Ignition Protected stern thruster assembly or any attempt
to disassemble anything on this thruster assembly inside the boat can cause an explosion with severe consequences. If there is a problem with your
Ignition Protected stern thruster, please contact your dealer.
