Side-Power SE IP-140 Installation Manual Download | Manualshive

Page: 24 / 28

background image

24

4526

8

2020

-

SE IP 50

MC_0033

Pre-delivery Checklist

EN

�.......... The bolts holding the gear house and motor bracket together are tightened correctly.

�.......... The bolts holding the motor to its bracket are tightened correctly.

�.......... All electrical connections are clean, dry and tight, and the correct cable, fuse and main

switch size.

�.......... Check that there is no electrical connection between the electro motor body and positive

terminal on the motor, and between the electro motor body and the negative (A1) terminal

on the motor with an ohm meter.

�.......... Anti-fouling has been applied to the gear house and propeller but NOT anodes, sealing/

rubber fi ttings or propeller shafts.

�.......... Propeller is fastened correctly to the shaft.

�.......... Propeller turns freely in tunnel.

�.......... The anode and/ or holding screw is tightened well with thread glue.

�.......... Check the boat for potential water leakage around installation areas.

�.......... Correct drive direction as per control panel.

�.......... User Manual is supplied to the owner.

The thruster has been installed as per the instructions in this manual and all points in checklist above have been controlled.

Signed: .........................................................................................

Date: .............................................................................................

Thruster type: ................................................................................................................................................................................................

Serial number:...............................................................................................................................................................................................

Date of delivery:.............................................................................................................................................................................................

Correct drive direction as per control panel: ..................................................................................................................................................

The compartment for the thruster has been isolated from general bilge water and has no obvious or suspected risks for fl ooding:

......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

......................................................................................................................................................................................................................

Other comments by installer: ........................................................................................................................................................................

.......................................................................................................................................................................................................................

.......................................................................................................................................................................................................................

«
...
22
23
24
25
26
...
»

Summary of Contents for SE IP-140





























Reviews:

No comments

Related manuals for SE IP-140

Brand: AOpen Pages: 101

EZ-USB HX2LP CY4605

Brand: Cypress Pages: 2

Brand: ASROCK Pages: 80

Brand: Zotac Pages: 54

MITX-DNV0 Series

Brand: Quanmax Pages: 84

Brand: Abit Pages: 48

Brand: DFI Pages: 5

Brand: Gigabyte Pages: 100

Brand: Biostar Pages: 37

Brand: Aaeon Pages: 74

Brand: ST Pages: 52

Brand: Texas Instruments Pages: 34

Brand: NXP Semiconductors Pages: 19

Brand: Quantum Design Pages: 59

Brand: Quantum Design Pages: 75

MOTORKIT-91F267-MC

Brand: Fujitsu Pages: 33

Brand: Fujitsu Pages: 30

Brand: Fujitsu Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands