background image

SIDESHIFT INSTALLATION GUIDE 

V1.7

 

 

      

19 

WARNING 

Retract the thruster only when the boat is at slow speed or 
completely stopped 

OPERATING THE WIRELESS REMOTE   

1.

 

For operation of the wireless key fob the joystick must be turned on and 
the thruster in the fully down position. 

2.

 

Push the top left or right buttons as required to operate the bow thruster.   

3.

 

Push the bottom left or right buttons to operate the stern thruster(if 
applicable). 

4.

 

The wireless key fob will automatically power-off after 5 seconds to 

preserve battery life. 

5.

 

A flashing green light indicates low battery.  No green light indicates a 
dead battery. 

6.

 

To replace the battery remove the 4 screws, open the case carefully, and 
insert a new CR2032 coin cell battery.  

OPERATION AND FAULT MODES   

 

Operation 

Action 

Features 

Power on thruster 

Press and hold joystick 

power button for 1 
second 

 

Short beep and solid blue 

light to confirm power 

 

Auto power-off after 5 min 

of non-use 

Lower thruster 

Push and release 
actuator down button 

on joystick 

 

Fast beep during 

deployment 

 

Slow beep when fully 

extended 

Operate thruster 

Push joystick left or 
right as required  

 

Retract thruster 

Push and release 
actuator up button on 
joystick 

 

Fast beep when thruster 
retracts 

 

System will power-off 

automatically once thruster 
is fully retracted 

Summary of Contents for PT230 PONTOON THRUSTER





























Reviews: