background image

5

/20

Assembly instructions

Electro-mechanical systems

A-opener 2.2

5

/20

09.2019

H39.ELEKS011EN-00

1.10 

Applicable documents

For the installation of the A-opener 2.2, it is essential 

to observe all assembly and operating instructions that 

are enclosed with other (optional) components.

1.11 

Appropriate disposal

Electrical devices should not be disposed of as house

-

hold waste. Bring the device, accessories and packaging 

to an environmentally-friendly recycling facility.

Safety

• 

All work on the 230 V AC mains power supply 

must be carried out in compliance with the current 

German VDE regulations (e.g., VDE 0100) and any 

relevant country-specific requirements.

• 

All-pole safety isolation should be used when rout

-

ing the network connection cable on-site.

• 

Any modifications to the A-opener 2.2 are prohibit

-

ed. 

• 

Wiring the unit incorrectly can irreparably damage 

its electronic components.

2.1 

Structure of the warning notes

The warning notes in these instructions 

• 

when observed, provide protection against potential 

personal injury and material damage, 

• 

classify the level of danger by the signal word,

• 

designate the danger of personal injury via the 

hazard sign,

• 

define the type and source of danger,

• 

show measures to prevent hazards and prohibit 

specific behaviour.

The warning notes are set up according to the following 

principle:

SIGNAL WORD

Type and source of danger

Explanation of the type and source of danger

• 

Measures for the prevention of the danger

The hazard sign designates warning notices that warn 

of personal injury.
The type and source of the hazard defines the cause of 

the hazard. The potential consequences of non-obser

-

vation of warning notices are e.g. danger to life due to 

electric shock.
Under measures, actions are listed that must be carried 

out for the prevention of hazards or which are prohibit

-

ed for the prevention of a hazard. 

2.2 

Warning notes used

DANGER

The signal word "Danger" designates an immediately 

threatening danger. If this hazard is not prevented, it 

leads to death or severe injuries.

WARNING

The signal word "Warning" designates a potential 

hazard. If this hazard is not prevented, it could lead to 

death or severe injuries.

CAUTION

The signal word "Caution" designates a potentially 

hazardous situation. If this hazardous situation is not 

prevented, it could lead to minor or moderate injuries.

NOTICE

The signal word "Note" defines actions for the pre

-

vention of material damage. The observation of these 

notes prevents damage to the components.

Information, advice etc.

This symbol indicates special features and designates 

facts that require increased attention.

2.3 

Warning notes

WARNING

Risk of fatal injury from electric shock and short circuit

Wrong connection of the A-opener

• 

All-pole safety isolation should be used when routing 

the network connection cable on-site.

• 

All work on the 230 V AC mains power supply must be 

carried out in compliance with the current German VDE 

regulations (e.g., VDE 0100) and any relevant coun

-

try-specific requirements.

If energy-carrying cables are routed in parallel to data 

cables (ISDN, DSL, etc.), this could lead to interference e.g. 

in the speed of the data transmission.

Summary of Contents for KFV A-Opener 2.2





















Reviews: