Siemens 1FK7 01. Instructions Manual Download

Page: 8 / 20

ENGLISH

610.40 700.21

Siemens AG

3.2

Features

Types of construction (EN 60034-7)

IM B5 (IM V1, IM V3)

Degree of protection (EN 60034-5)

IP64 (1FK701.: IP54)

Cooling (EN 60034-6)

Self-cooling

A-grade sound pressure level (EN 60034-9)
for speed range up to 3,000 rpm

1FK701. - 1FK704.

approx. 55 dB(A)

1FK706.

approx. 65 dB(A)

1FK708., 1FK710.

approx. 70 dB(A)

Thermal motor protection (EN 60034-11)

Temperature sensor KTY84
in the stator winding

Shaft end (DIN 748-3; IEC 60072-1)

cylindrical; without keyway,
Tolerance range k6 (1FK701.: h6)

true running, coaxiality, axial run-out deviation Tolerance N
(DIN 42955; IEC 60072-1)
Oscillating quantity level (N 60034-14)

level A (up to rated speed)

Bearing design

Rolling contact bearing with permanent
grease lubrication (lifetime lubrication)
fixed bearing on non-drive end

Service life of bearing

20000 h (guideline)

Winding insulation (EN 60034-1)

Temperature class 155 °C (311 °F) (F)

Ambient temperatures

-15 °C to +40 °C (5 °F to 104 °F)
otherwise the rated data are reduced
(see Configuration Manual)

Installation altitude (EN 60034-1)

up to 1000 m a.s.l,
otherwise the rated data are reduced
(see Configuration Manual)

Magnetic material

Rare-earth material

Electrical connections

Revolving plug for output and
encoder signals

Encoder system

fitted encoder
- speed recording
- recording the rotor position
- indirect positional recording

Options/expansions

Low inertia series

HD (High Dynamic)

Type of protection (EN 60034-5)

IP65; additional drive end flange IP67

Fitted/mounted elements

- closed current holding brake (DIN VDE 0580)
Supply voltage 24 V DC ±10%
- planetary gearing

Encoder system

- incremental encoder sin/cos 1 V

- absolute value encoder EnDat
- simple, absolute value encoder
- resolver

Encoder system without
DRIVE-CLiQ Interface

- I2048S/R = incremental encoder sin/cos 1 V

2048 S/R

- AM2048S/R = absolute value encoder EnDat
- AM512S/R = absolute value encoder EnDat
- AM32S/R = absolute value encoder EnDat
- AM16S/R = absolute value encoder EnDat
- resolver

Summary of Contents for 1FK7 01.





















Search results

Summary of Contents for 1FK7 01.

Reviews:

Related manuals for 1FK7 01.

Brands by name

Popular brands

Siemens 1FK7 01., Instructions Manual

Search results

Summary of Contents for 1FK7 01.

Reviews:

Related manuals for 1FK7 01.

Brands by name

Popular brands