Siemens 3VA1 100 A Manual Download

Page: 131 / 532

Applications

3.2 Use of the 3VA1 breaker as a switch disconnector

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

131

Protection of 3VA1 switch disconnectors at 50 / 60 Hz by a 3VA1 molded case circuit breaker

More combinations can be found on the Internet (

http://www.siemens.com/3VA-

Documentation

Combinations with other protective devices can be configured at any time by means of

SIMARIS design or using the characteristics maximum let-through energy I

max

and

maximum let-through current I

c max

of the 3VA1 switch disconnector. You will find these

characteristics in the technical product data sheets and in the table in chapter Overview of

3VA1 as switch disconnectors (Page 130).

Note
In the event of a fault, all switching devices in the affected branch must be function-tested

(see Regular maintenance (Page 419)).

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands