Siemens 3VA1 100 A Manual Download | Manualshive

Page: 136 / 532

background image

Applications

3.4 400 Hz network applications of 3VA molded case circuit breakers

3VA molded case circuit breakers

136

Manual, 04/2015, A5E03603177010-02

Note
DC 2-pole (all-pole disconnection), non-grounded system
If there is no possibility of a double ground fault occurring, or if any ground fault that does

occur is dealt with immediately (ground-fault monitoring), 500 V will be the maximum

permissible direct voltage. In a non-grounded system, all poles must be disconnected.

Further circuits are available on request.

3.4

400 Hz network applications of 3VA molded case circuit breakers

400 Hz networks are used for:

●

Ground power supply systems for aircraft

●

On-board electrical systems of marine craft and aircraft

●

Other external stations of airports which are protected by uninterruptible power supplies,

e.g. radar installations, data processing equipment, communication systems

It is important to supply the on-board electrical systems of aircraft with a very smooth DC

voltage. This can be generated more easily by 400 Hz power supplies than by 50 Hz

networks. Moreover, the power transmitters (transformers) are smaller and lighter by

comparison with 50 Hz networks, two important arguments for using 400 Hz on-board

electrical systems in aircraft and some marine craft.

Suitable 3VA molded case circuit breakers and trip units

3VA molded case circuit breakers equipped with 2-series thermal-magnetic trip units are

suitable for use in 400 Hz networks.

«
...
134
135
136
137
138
...
»

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3VA1 100 A

Brand: ABB Pages: 60

Brand: LOVATO ELECTRIC Pages: 4

Brand: Westinghouse Pages: 32

Brand: nader Pages: 25

150VCP-W Series

Brand: Eaton Pages: 17

Digitrip RMS 610

Brand: Cutler-Hammer Pages: 24

Brand: ABB Pages: 34

Brand: ABB Pages: 4

Digitrip OPTIM 1050

Brand: Cutler-Hammer Pages: 66

Brand: Linear Technology Pages: 9

Brand: Extel Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands