Siemens 3VA1 100 A Manual Download

Page: 300 / 532

Accessories

4.8 Residual current devices

3VA molded case circuit breakers

300

Manual, 04/2015, A5E03603177010-02

4.8.2

Residual current devices for mounting on circuit breakers

The RCD310, RCD510, RCD320, RCD520 and RCD820 residual current devices are

available as accessories for mounting on specific 3VA molded case circuit breakers up to the

largest circuit breaker size/current rating.

Combination with circuit breakers

After a residual current device has been mounted on a molded case circuit breaker or switch

disconnector, the specifications of the breaker or disconnector remain unchanged with

respect to the following characteristics:

●

Standards

●

Conductor cross-sections

●

Use of connection accessories

●

Isolating features

●

Selective behavior

When a basic type residual current device is mounted on a 3VA1 molded case circuit

breaker or a 3VA1 switch disconnector, the electrical rating of the equipment combination is

automatically downgraded to the lower electrical rating of the residual current device.
Example:

: 3VA1

≤ 690 V AC

3VA1 and Basic residual current device

≤ 480 V AC

For more information, refer to chapter Technical specifications (Page 352).

Residual current devices

Standards
The combination of molded case circuit breaker and residual current device conforms to

IEC 60947-2 Annex B.

Power supply
The residual current devices do not require an external power supply, but tap a supply from

the main current paths of the molded case circuit breaker or switch disconnector.

Guaranteed to function properly
Proper functioning of the residual current device is guaranteed even with only one phase and

N (applies to RCD320, RCD520 and RCD820) or two phases (alternating current or

pulsating direct voltage).

Direction of incoming supply
The direction of incoming supply to the combination of circuit breaker and residual current

device is optional, i.e. it can be connected at the top or bottom. The performance of the

residual current devices is not impaired by regenerative feedback from motors.

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands