Siemens 3VA1 100 A Manual Download

Page: 347 / 532

Accessories

4.8 Residual current devices

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

347

Installation

Installation
Regardless of the type of connection system installed on the 3VA2 molded case circuit

breaker, the RCD820 is mounted underneath the electronic trip unit of the circuit breaker.
1.

Dismantle the loadside connection components of the molded case circuit breaker and

install the supplied connection components for the residual current device.

Insert the residual current device into the T slots of the molded case circuit breaker.

Push the residual current device backwards until its rear panel is flush with the rear panel

of the molded case circuit breaker.

Screw the molded case circuit breaker to the residual current device. Special connecting

screws are provided on the line side of the residual current device for this purpose.

Place a contact hazard protective cover over the circuit breaker/RCD assembly.

Reinstall the loadside connection components of the molded case circuit breaker at the

outgoing feeder end of the residual current device.

Attach the assembly to a mounting plate using the fastening screws.

Note
Since the outgoing feeder end of the residual current device has exactly the same

connection contours as the 3VA2 molded case circuit breaker, all connection accessories

such as phase barriers, terminal covers, etc. can also be mounted on the residual current

device.

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands