Siemens 3VA1 100 A Manual Download

Page: 411 / 532

Accessories

4.13 Escutcheon

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

411

4.13

Escutcheon

Molded case circuit breakers or supplementary motor operators or front mounted rotary

operators for molded case circuit breakers are often installed in cubicles or distribution

boards in such a way that only the operating device is directly accessible. Busbars, cables

and the termination area of the molded case circuit breaker are covered by metal or plastic

plates in order to prevent direct contact with live components. The cubicle door itself is often

designed as a protective cover.
Cutouts must be made in these covers

●

in order to allow access to control elements,

●

which are designed to prevent direct contact with cables, and

●

which are large enough in size that the cover can be closed easily.

All these requirements necessitate gap dimensions of a few millimeters between the cutout

and the unit.
Escutcheons are installed in cases where the gap size needs to be minimized and the gaps

covered. The use of escutcheons makes for a clean-lined, attractive cubicle front face and

provides a higher degree of protection (IP30).

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands