Siemens 3VA1 100 A Manual Download

Page: 501 / 532

Technical specifications

6.4 Derating and temperature compensation

3VA molded case circuit breakers
Manual, 04/2015, A5E03603177010-02

501

6.4.7

Derating for the electronic trip units of 3VA2 molded case circuit breakers

The current measuring circuits of the electronic trip units of 3VA2 molded case circuit

breakers are not affected by the ambient temperature. The Rogowski coils integrated in the

trip unit measure the current and compare it to the set tripping threshold. Higher or lower

ambient temperatures do not influence the tripping threshold, which means that it is not

necessary to apply correction factors.

Limitation of the rated operational current
The temperature inside the molded case circuit breaker is nonetheless influenced by the

ambient temperature and the current-dependent power loss generated inside the unit. To

prevent overloading of molded case circuit breakers under difficult thermal conditions, the

maximum rated continuous operational current must therefore be limited as a function of the

ambient temperature in some cases:
The table below specifies the maximum rated continuous operational current as a function of

the ambient temperature and the installed accessories. The operational current must never

exceed the maximum rated operational current of the molded case circuit breaker.

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands