Siemens 3VA1 100 A Manual Download | Manualshive

Page: 126 / 532

background image

Applications

3.2 Use of the 3VA1 breaker as a switch disconnector

3VA molded case circuit breakers

126

Manual, 04/2015, A5E03603177010-02

3.2

Use of the 3VA1 breaker as a switch disconnector

Switch disconnectors are deployed as:

●

Disconnectors in subdistribution and final distribution boards

●

Bus couplers

●

Disconnectors for machine line-ups, e.g. as maintenance or repair breakers

●

Operator controls and disconnectors for cables, busbars and device line-ups

●

Application as mains supply disconnectors

●

Application as main switches

●

Isolation of small distribution systems in industrial/commercial buildings

●

Disconnection of loads

Switch disconnectors are capable of switching equipment and parts of electrical installations

when they are conducting their operational current under normal operating conditions.
Switch disconnectors do not have an overload or short-circuit release. For this reason, a

molded case circuit breaker or a fuse must be installed upstream of every switch

disconnector. Refer to chapter Upstream protection of switch disconnectors (Page 130).

Compatibility of 3VA switch disconnectors and accessories

3VA1 switch disconnectors have been developed from the 3VA1 molded case circuit breaker

design. Both share the same attributes listed below:

●

Sizes

●

Dimensions

●

Mounting options

●

Procedure for installing accessories

This means that a shunt trip can trip the switch disconnectors by remote control, or that the

disconnector can be opened or closed by a side wall mounted rotary operator.

«
...
124
125
126
127
128
...
»

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3VA1 100 A

Brand: GE Pages: 10

Brand: GE Pages: 7

Brand: GenInterlock Pages: 2

BC160NT305 Series

Brand: OEZ Pages: 17

Brand: Zumtobel Pages: 4

POWELL PowlVac-ND

Brand: Safety Pages: 63

Brand: Westinghouse Pages: 38

DE-ION 150-DH-250-A

Brand: Westinghouse Pages: 21

Brand: TAVRIDA ELECTRIC Pages: 172

FUSEMATIC FM25-600

Brand: FEDERAL PACIFIC Pages: 12

Brand: ABB Pages: 42

Brand: GE Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands