Siemens 3VA1 100 A Manual Download

Page: 262 / 532

Accessories

4.6 Motor operators

3VA molded case circuit breakers

262

Manual, 04/2015, A5E03603177010-02

4.6.1.1

MANUAL, AUTO and LOCK modes

The motor operator MO320 is switched to MANUAL or AUTO mode when the plastic window

is opened (MANUAL) or closed (AUTO).

MANUAL:
When the plastic window is open, the motor operator MO320 is in MANUAL mode. The

motor operator is moved to position ON (I) or OFF (O) by manual operation of the handle.

AUTO:
When the plastic window is closed, the motor operator MO320 is in AUTO mode. The motor

operator can be operated via control cables, e.g. in response to signals issued by a

pushbutton or by control commands output by a PLC.

LOCK:
The motor operator can be locked in the OFF (O) position to prevent reclosure of the

breaker. The padlock locking device snaps out if the slide above it is moved to the "LOCK"

position.
Up to three padlocks with a shackle diameter of between 5 and 8 mm can be inserted

through the openings in the padlock locking unit. Padlocks are not included in the scope of

supply.

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands