Siemens 3VA1 100 A Manual Download

Page: 60 / 532

Description

2.5 Standards and guidelines

3VA molded case circuit breakers

Manual, 04/2015, A5E03603177010-02

2.5.2

Electromagnetic compatibility

The 3VA molded case circuit breakers meet the requirements of the following standards:

●

CISPR11, Class A and Class B

●

IEC / EN 60947-1, Appendix S

●

IEC / EN 60947-2, Appendices B, F, J and N

The 3VA molded case circuit breakers are adequately resistant to the following factors:

●

Electrostatic charge

●

Electrostatic discharge

●

Electromagnetic waves, e.g. from transmission systems, mobile phones, radio telephone

sets and radar systems

●

Overvoltage, e.g. caused by lightning

●

Voltage surges

2.5.3

Certificates

You can find information on the available certification (CE, UL, CSA, FM, marine approvals)

on the Internet (

http://support.automation.siemens.com/WW/view/en/54137334/134200

In the Entry List you can use the certificate type (general product approval, explosion

protection, test certificates, shipbuilding, etc.) as a filter criterion.

2.5.4

Ambient conditions

Pollution degree

Operation of the 3VA1 and 3VA2 molded case circuit breakers is approved in accordance

with IEC / EN 60947-1 and IEC / EN 60664-1 for pollution degree 3.

Ambient temperature

3VA molded case circuit breakers are used at ambient temperatures from -25 °C to +70 °C.

Derating (reduction in rated operational current) is required at temperatures above +50 °C.

You will find more information on the applicable derating factors in chapter Derating and

temperature compensation (Page 489).
The permissible storage temperature in original Siemens packaging lies between -25 °C and

+80 °C.

Special climatic requirements

3VA molded case circuit breakers including their accessories can also be used in

challenging operating environments.

Summary of Contents for 3VA1 100 A





















































































































































































































































































































































































































































































































































Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands

Siemens 3VA1 100 A, Manual

Search results

Summary of Contents for 3VA1 100 A

Reviews:

Related manuals for 3VA1 100 A

Brands by name

Popular brands