background image

 

SIMATIC MV320 / SIMATIC MV325 
Operating Instructions, 08/2015, C79000-G8976-C352-03 

53

 

 

Appendix 

A.1

 

Code configurations 

 

 

Note 
Changing the configuration 
Changes to the configuration take effect immediately and are stored. 

 

 

Note 
Rate of data transmission depends on set keyboard 
Note that the data transmission rate is slower with a set universal keyboard (Universal 

Keyboard Mapping) than with selection of a specific keyboard language (e.g. US keyboard). 

 

SIMATIC MV320 

Codes for configuration of the device 
A current list of the codes for configuration of the SIMATIC MV320 reader is available at the 

following link: 
SIMATIC MV320 Configuration guide 

(

https://support.industry.siemens.com/cs/ww/en/ps/15160/man

) 

 

Motion detection with the reader with and without stand detection 
If the reader is placed on a stand, the reader with stand detection automatically switches to 

the motion detection mode. 

 

When the code for "Disable Motion Detection with Stand Detection" is scanned in, the 

reader switches to the motion detection mode. Detection depends on whether or not the 

reader is on a stand. 

 

To disable motion detection, you need to scan in the code for "Disable Motion Detection 

with Stand Detection" and "Motion Detection Scanning Off". 

 

To enable motion detection on readers with stand detection after disabling motion 

detection: 
You need to scan in the code for "Enable Motion Detection with Stand Detection" 

 

To enable motion detection on readers without stand detection: 
You need to scan in the required code for "Motion Detection On". 

Summary of Contents for 6GF3320-0HT01

































































Reviews: