manualshive.com logo in svg

Siemens Climatix Series, Basis Document

The Siemens Climatix Series is a state-of-the-art HVAC control system that ensures optimal climate management. With our user-friendly interface and intuitive features, you can easily operate and maintain your Climatix device. Download the short manual for free on our website to maximize the efficiency of your HVAC system.

Share
Download
background image

 

105 / 244 

Siemens 

Standard application AHU 

CE1P3977en_02 

Building Technologies 

Detail pages: Inputs and outputs 

01.02.2010 

6.5.3  Special information 

 

•

  Read: Levels 6, 4 and 2. 

•

  Write: Read only. 

 

 

Parameter 

Range 

Function 

BACnet present 

Value 

Depends on hardware. 

Present value on BACnet. Value is frozen for an 

alarm. 

Value selector 

 

 

–  Hardware 

–  Comm 

–  Average 

 

 

 

–  Minimum 

 

 

 

–  Maximum. 

 

 

 

–  PreferedHW 

 

 

 

 

–  PrefComm 

Displays valid input value for the application: 

–  Value on hardware input. 

–  Value from communications. 

–  Average from values on the hardware input and 

communications. An alarm is triggered when one of 

the two values are invalid (if enabled). 

–  Lowest value from the values on hardware input 

and from communications. Alarm triggers (if en-

abled), if one of the two values is invalid. 

–  Highest value from the values on hardware input 

and from communications. Alarm triggers (if en-

abled), if one of the two values is invalid. 

–  Value on hardware input has priority. The value 

from communications assumed if invalid. Alarm 

triggers (if enabled), if both values are invalid. 

–  Value from communications has priority. The value 

from hardware input assumed if invalid. Alarm trig-

gers (if enabled), if both values are invalid. 

Value HW 

Depends on hardware. 

Present value for hardware. 

Value comm 

Depends on hardware. 

Present value from communications. 

Reliability HW 

Depends on hardware. 

Present reliability of hardware value. 

Reliability comm 

Depends on hardware. 

Present reliability of value from communications. 

Disable OffNormal 

 

 

 

–  Passive 

–  Active 

The OffNormal alarm is disabled. Example: A value 

greater than the high limit does not trigger an alarm: 

–  Alarm is triggered. 

–  Alarm is not triggered. 

    ToOffNormal 

Day of week, dd.mm.yyyy  

hh:mm:ss 

Date and time the last off normal alarm occurred. 

    ToFault 

Day of week, dd.mm.yyyy  

hh:mm:ss 

Data and time last fault alarm (Reliability <> 0) oc-

curred. 

    ToNormal 

Day of week, dd.mm.yyyy  

hh:mm:ss 

Date and time last alarm was reset. 

Access level 

Parameter 

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 105

Summary of Contents for Climatix Series





















































































































































































































































Reviews:

No comments

Related manuals for Climatix Series

ABB FPBA-01 PROFIBUS DP Quick Installation And Start-Up Manual preview
FPBA-01 PROFIBUS DP
Brand: ABB Pages: 2
ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Brand: ABB Pages: 4
U-Line H-3934 Manual preview
H-3934
Brand: U-Line Pages: 7
Acclaim Lighting Canvas User Manual preview
Canvas
Brand: Acclaim Lighting Pages: 32
Lamtec ETAMATIC Manual preview
ETAMATIC
Brand: Lamtec Pages: 136
Magicfx FX-COMM4NDER MFX3203 User And Installation Manual preview
FX-COMM4NDER MFX3203
Brand: Magicfx Pages: 16
Becker Centronic SunWindControl SWC245-II Assembly And Operating Instructions Manual preview
Centronic SunWindControl SWC245-II
Brand: Becker Pages: 52
Quickie R-net Instructions For Use Manual preview
R-net
Brand: Quickie Pages: 108
GARDINER TECHNOLOGY GARDTEC 590 User Instructions preview
GARDTEC 590
Brand: GARDINER TECHNOLOGY Pages: 28
G&D PersonalWorkplace Pro Video Installation Manual preview
PersonalWorkplace Pro Video
Brand: G&D Pages: 56
Beninca DA.93AM Operating Instructions Manual preview
DA.93AM
Brand: Beninca Pages: 16
Festo CPX-AP-I-8DI-M8-3P Translation Of The Original Instructions preview
CPX-AP-I-8DI-M8-3P
Brand: Festo Pages: 18
Woodward 723PLUS Original Instructions Manual preview
723PLUS
Brand: Woodward Pages: 118
M-system R7C-DC8C Instruction Manual preview
R7C-DC8C
Brand: M-system Pages: 9
Bailey Infi 90 IMSPM01 Instruction preview
Infi 90 IMSPM01
Brand: Bailey Pages: 52
Fastech Ezi-IO EtherCAT DA User Manual preview
Ezi-IO EtherCAT DA
Brand: Fastech Pages: 52
Cooper S225-50-45 Service Information preview
S225-50-45
Brand: Cooper Pages: 4
Trenz Electronic TE0726 Manual preview
TE0726
Brand: Trenz Electronic Pages: 21

Brands by name

Popular brands

Load more brands