Siemens Climatix Series Basis Document Download

Page: 159 / 244

159 / 244

Siemens

Standard application AHU

CE1P3977en_02

Building Technologies

Configuration

01.02.2010

15.2 Configuration 2

Subfunctions for parts of plants occurs in Configuration 2.

Configuration 1 completed with reset.

– Configuration occurs setting-by-setting, i.e. you cannot bypass any lines.

– Configuration 2 must be completed with reset prior to starting Configuration IOs.

As required: Enter password for level 4:

Start page > Password Enter

then:

Main Index > Configuration > Configuration 2

Parameter

Range

Function

Night cooling

Yes

Free cooling.

Requirement: Night cooling can only be selected if one outside air

temperature sensor and one room or return air sensor is available.

The night kick function is enabled automatically if only one return air

sensor with saving property is available. If the return air sensor saves

values, the stored temperature is used to start night cooling.

Tmp start

Starts plant at night based on temperature difference.

Requirement: Function can only be selected if one room or return air

sensor is available.

The night kick function is enabled automatically if only one return air

sensor with saving property is available. If the return air sensor saves

values, the stored temperature is used to start.

Function not enabled.

Htg

Function enabled for heating only.

Clg

Function enabled for cooling only.

Htg+Clg

Function for enabled heating and cooling.

Boost

Plant boost with heating and cooling to a separate setpoint.

Requirement: Function can only be selected if one room or return air

sensor is available.

Function not enabled.

Htg

Function enabled for heating only.

Clg

Function enabled for cooling only.

Htg+Clg

Function for enabled heating and cooling.

Tmp start/OSSTP

blk

Block dampers or exhaust air fan when the plant is started via boost

or temperature differential.

Note: The function is implemented for energy considerations.

Caution: A bypass damper must exist and be open when the

function is enabled. Otherwise, it may damage the plant.

None

No block.

Damper

Dampers remain closed.

Fan

Dampers remain closed and only the supply air fan is started.

Damper fdbk

No damper feedback.

One

Feedback for supply air dampers (or a common feedback for both

dampers). Digital input for feedback.

Two

Separate feedback for supply and exhaust air damper. Two digital in-

puts for feedback.

Task

Prerequisite

Notes

Start

Basis Document Siemens Climatix Control System
BDCX.100820.01GB

Page 159

Summary of Contents for Climatix Series





















































































































































































































































Search results

Summary of Contents for Climatix Series

Reviews:

Related manuals for Climatix Series

Brands by name

Popular brands

Siemens Climatix Series, Basis Document

Search results

Summary of Contents for Climatix Series

Reviews:

Related manuals for Climatix Series

Brands by name

Popular brands