background image

 

Installing/connecting 

 

4.1 Installing and connecting the CP 1625 

CP 1625 / CP 1625Dev 
Operating Instructions, 04/2018, A5E43075902-AA 

21

 

Installing and connecting the CP 1625 

 

 

Note 
Installation only with power disconnected 
Opening the PC and inserting or removing submodules is only permitted when the power is 

disconnected. 

 

Proceed as follows when installing and connecting the CP 1625: 
1.

 

Turn off your PC and pull out the power cable connector from the socket. 

2.

 

Open the PC housing as described in your PC manual. 

3.

 

Remove the cover of a free PCI slot in your PC. 

4.

 

Take the CP 1625 out of the packaging. 

 

 

 

Note 
When handling the communications processor, make sure that you do not touch the 

connectors or the electronic components. 

 

5.

 

Insert the CP 1625 into the PCIe slot according to the instructions. Make sure that the  

CP 1625 is inserted securely and evenly in the slot socket. 

6.

 

Close the PC housing as described in your PC manual. 

7.

 

Insert the connecting cable (TP) into the corresponding socket on the front panel of the 

CP 1625. 

8.

 

Insert the power plug into the power socket again. 

9.

 

Switch on your PC. 

Passive network components 

You will find important notes on the use of passive network components in the document 

"Industrial Ethernet / PROFINET Passive network components" 

(

https://support.industry.siemens.com/cs/ww/en/view/84922825

).  

Siemens Automation Parts

Summary of Contents for CP 1625
































Reviews: