en
Rapid heating
14
‒
The light above the
button goes out.
a
The appliance switches off. Any functions currently
in progress are cancelled.
a
The time or residual heat indicator appears in the
display.
8.3 Starting operation
You must start each cooking operation.
ATTENTION!
If there is water on the cooking compartment floor
when operating the appliance at temperatures above
120 °C, this will damage the enamel.
▶
Do not use the appliance if there is water on the
cooking compartment floor.
▶
Wipe away any water on the cooking compartment
floor before operation.
▶
Press
to start the operation.
a
The settings, the run time and the heat-up line ap-
pear on the display.
8.4 Pausing or cancelling operation
You can briefly pause the operation and then continue.
If you cancel the operation completely, the settings are
reset.
1.
To pause the operation briefly:
‒
Briefly press
.
‒
To continue the operation, press
.
2.
To cancel the operation, press
.
a
The operation stops and all of the settings are reset.
8.5 Setting an operating mode
Requirement:
The appliance must be switched on.
1.
Press
.
The operating modes menu opens.
2.
Press the operating mode that you require.
Various options are available depending on the op-
erating mode.
3.
The selection can be changed using the rotary se-
lector.
Change any further settings depending on the selec-
tion.
4.
Press
to start.
8.6 Setting the type of heating and the
temperature
When you switch on the appliance, the types of heating
operating mode is set automatically.
1.
Turn the rotary selector to select the required type
of heating.
2.
Press the temperature.
3.
Use the rotary selector to set the temperature.
4.
Press
to start the operation.
a
The appliance starts heating.
a
The set type of heating, temperature and cooking
time/appliance run time are shown in the display.
5.
When the food is ready, press
to switch the
appliance off.
Tip:
The most suitable type of heating for your food
can be found in the type of heating description.
Note:
You can also set a cooking time and an opera-
tion end time on the appliance.
"Time-setting options", Page 15
Changing the type of heating
When you change the type of heating, the other set-
tings are also reset.
1.
Press
to pause operation.
2.
Press the type of heating.
3.
Turn the rotary selector to select the required type
of heating.
a
The corresponding recommended temperature ap-
pears on the display.
Changing the temperature
Once the operation has started, you can change the
temperature directly.
▶
Use the rotary selector to change the temperature.
a
The temperature is applied immediately.
8.7 Displaying information
In most cases, you can call up information about the
function that you have just started. The appliance auto-
matically displays certain information, e.g. to ask you to
do/confirm something or to issue a warning.
▶
Press
.
a
When available, information is displayed for a few
seconds.
9 Rapid heating
To save time, you can shorten the preheating time for
set temperatures of 100 °C and higher.
You can use rapid heating for this type of heating:
¡
4D hot air
¡
Top/bottom heating
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note:
Do not set a cooking time until rapid heating has
come to an end.
1.
Set a suitable type of heating and a temperature of
at least 100 °C.
2.
Press .
a
The symbol appears on the left of the display
next to the temperature.
a
The progress line begins to fill up.
3.
a
When rapid heating has come to an end, a signal
tone sounds. The symbol disappears from the
display.
4.
Place the food in the cooking compartment.
Cancelling rapid heating
▶
Press .
a
The symbol disappears from the display.
Summary of Contents for CS856GN.7
Page 51: ......
