Siemens DE1113407, Installation Instructions Manual

7

en

Congratulations on purchasing this Siemens appliance. You 
have acquired a top-quality product, which will give you a lot 
of enjoyment.

Installation instructions

These installation instructions apply to various continuous-
flow heater appliance models. Therefore the illustrations 
may deviate from the device you bought.

■

Install the appliance as shown in the illustrations. The 
 illustrations can be found in the centre of the instruction 
manual. Observe the instructions in the text.

Installation

I.

Unpacking/Removing the cover

■

Unpack the appliance and check for transport damage. If 
any components are damaged, then do not connect the 
appliance.

■

Check that your appliance contains all components in-
cluded in the scope of delivery: appliance, installation 
set with supplementary sheets, installation instructions, 
operating instructions.

■

Please dispose of the packaging and the old appliance in 
an environmentally-friendly manner.

■

When removing the cover from either a Type  A  or 
Type  B  appliance, please note the following: 
The Type  A  cover is fastened by a central closure behind 
the service flap.
The Type  B  cover is attached by two screws located on 
the underside of the cover.

II.

Preparations for installation

Important: Only use the supplied installation set. 
The supplied water connection nozzles must be installed!

■

Shut off water supply. The electrical connection (connec-
tion cable) must be disconnected from the power supply. 
Unscrew the fuse or switch off the circuit breaker.

■

Install the water connection nozzles according to the in-
structions on the supplementary sheet.

■

The electrical connection cable can either be guided in at 
the top (X) or bottom (Y).

■

The rear panel must lie against the cold water connection 
nozzle in the position provided for such (Fig. II., 8.).

III.

Wall mounting

■

The grommet must tightly surround the connection cable. 
If it is damaged during mounting, the openings must be 
provided with watertight sealing.

■

The electrical supply terminal can be fitted at the top (X) 
or bottom (Y). The sheath of the connection cable must 
extend for at least 40 mm into the appliance.

■

The distance to the wall is variable. You can compensate 
for any unevenness of the wall’s surface. With a distance 
to the wall of 8–16 mm, insert the spacer and install the 
extender (Fig. III., 3. – 5.).

■

The appliance must be mounted securely on the wall. If nec-
essary, attach it at the lower adjustable screws (Fig. III., 6.).

IV.

Water connection

■

Connect the water supply, then open the cold water supply.

■

The appliance must be vented. To do so, open the 
warm water tap fully and flush out the appliance 
 thoroughly for 1 minute.

V.

Electrical connection/Mounting

■

Only for appliances with power selector switches: 
Set the power using the power selector switch before 
 connecting the wires to the mains connection terminal: 
Nominal output power left, reduced output right 
(Fig. V., 1.) and the set output marked on the ratings plate. 

■

Screw the wires tightly into the mains connection terminal.

■

Switch on the safety limiter (Fig. V., 3.)

■

Install the cover – according to either Type  A  or  B  in-
structions (Fig. V., 4. – 7.).

Installation note

■

The installation of non plug-in ready appliances must 
be undertaken by the respective utility operator or by 
a qualified specialist company, who can also assist you 
when you are requesting the approval of the utility 
company for installation of the appliance.

VI.

Startup

The device is compliant to IEC 61000-3-12.

First start-up

■

Switch on the fuses.

■

Setting the temperature.

■

Initial rinsing: Open the warm water tap fully and allow 
water to flow for at least 1 minute. Only then (for safety 
reasons) will the appliance begin to heat.

Tip: Should the appliance not start because of a reduced 
flow-rate, remove the perlator, shower head or similar before 
start and repeat the process.

■

Explain the operation of the appliance to the user.

VII.

Additional information

■

If the appliance does not have sufficient water flow due 
to low water line pressure in your domestic plumbing sys-
tem, remove the flow-rate limiter (Fig. VII., 1. – 3.).

■

Priority circuit for the combination with electrical  storage 
heaters:
For operation with a priority circuit, a special load shed-
ding relay BZ 45L21 (special accessory) is required.  Other 
existing load shedding relays, with the exception of elec-
tronic load shedding relays, may malfunction (Fig. VII., 
Wiring diagram).

■

The control electronics must be coded when operated 
with a load shedding relay. Remove the keying nose on 
the electronics (Fig. VII., 4.).